Search results

Recently got a 97 with 4.0 that looked like the oil hadn't been changed in several years and moisture had gotten into the crankcase. The is massive buildup on everyhing. I have pulled the head and taken it to be milled and dipped and dropped the pan to change the pump. What can I use to...

Is there any reason the lines from the prop valve to the mc shouldn't be steel braided instead of hard lines?

Like the title says 23 spline AW4 from a 91-95. Prefer good condition and cheap. Thanks

I think the AW4 in the wife's 93 ZJ just finally gave out. I was stopped and let it idle for about 5 minutes and when I went to go it didn't want to pull. It has done the same thing a couple of times in the past year and each time I drained and refilled it and replaced the filter. This time...

I'm not getting much help in OE Tech and I'm almost at my wits end with this issue. Every time I think I've got it fixed the problem is still there. http://naxja.org/forum/showthread.php?t=1030038 Thanks

93, 4.0, auto It has had a slow start since I got it about a year ago. The previous owner had removed the fuel rail and I noticed the #3 injector was leaking onto the manifold and has been for some time. I removed the rail and found no upper o-ring on the #3 and 2 upper o-rings on the #1, so...

First off not an XJ, but a 93 ZJ with the 4.0/aw4/231. Engine has been replaced but if the tranny is original it has almost 300K. Problem started about a week ago when I felt the tranny slip in 1st gear. It did it a few times and then drove like normal again and I didn't think anything else...

Rusty's engine/tranny skid for short arms. It has been on my rig for about 1 year and I am removing because it is not compatible with the drop brackets I have just installed. It is 3/16 and still straight. There is some surface rust where the powdercoat is peeling, but structurally sound...

I have just redone all the brakes on the wifes ZJ (93, 4.0, AW4, 231). I started this process because there was a annoying squeal. I started by replacing the calipers and pads. Then on the back I replaced everything except the wheel cylinders. I applied anti-seize to the front and the squeal...

I have little time to either work on or wheel my rig, so I think it might be time to let it go. It has all the original drivetrain with less than 101K. 4.0, aw4, 242, non-disco 30, 35 rear (both open with 3.55's). Under the hood: new Optima Red top Rusty's intake tube with cone filter aluminum...

I was just giving the wife's new DD (93 ZJ 4.0) the seafoam treatment when I saw antifreeze start to dribble onto the ground. When I got down under it to check it, both the second and third freeze plugs (from the front on the side) are leaking. The second is not so bad, but the third was...

I just got a 93 ZJ for the wife for a great deal with a leaking water pump. I just got it apart and when I took the mounting bolt a 9 o'clock (passenger side of the shaft) out, fluid poured out the hole. It appears that the PO ran the one long bolt in the wrong hole and busted the casting on...

Does anyone know anything about them? I have found a good deal on a 91. I have been told there is some bottom end noise and am having some problems sourcing parts. I know the engine is a Toyota 1.6 SOHC. Is there another vehicle that was sold in the states with the same engine I could find...

I'm looking for a ZJ for the wife for a DD. I do not want the V8 (unless it is the 98 360) and do not want the full time AWD. I think the prefect find would be 4.0 with the 242...and cheap. Anybody have anything?

I searched and most results I found deal with smoke on acceleration, but what I have is smoke at idle after warmup. I first noticed it about a week ago and thought the rings were gone it was so bad. I checked the oil and it was a little low, but not enough to cause any issues. When I got it...

I got a set of steel rims off ebay and had to drive about 80 miles to get them, but I got a really good price. When I got to the guy's house to pick them up I noticed about 6 XJ's behind the barn and asked if he was parting them out. He said yes, and I was hoping to find a D44 under one of...

What are the pros and/or cons of this axle. I have searched, but didn't find anything that looked helpful. Is anyone running this axle or have any good info to share? forgot to mention for the rear...I think the front should be the wrong side drop. Thanks

http://knoxville.craigslist.org/pts/946415400.html

I have a leak out of the back of my 242 around the slip yoke of my driveshaft. I just replaced the seal, but the parts store didn't have one listed for the 242 and I compared my old seal to the one they had listed for the 231 and they appeared identical in size. The seal is properly installed...

I have a rear disk setup from a 97 Crown Vic. It includes the backing plates with all springs and hardware for e-brakes (missing 2 pins that hold the e-brake shoes on) and calipers with mounting bolts. No pads or shoes or rotors. $75.00 shipped to your door with insurance. I do take PayPal...