• Welcome to the new NAXJA Forum! If your password does not work, please use "Forgot your password?" link on the log-in page. Please feel free to reach out to [email protected] if we can provide any assistance.

Recent content by BonesBrosChris

  1. BonesBrosChris

    Fitting 2500 front end parts:

    I sold the truck last month to a guy in Utah. I did toss on the bumpers before it left but he didn't like the look so I think he's going to change them. He took off the Goodyear MT's and put on all terrains as well as a canopy on the bed. I do have some misc 2500 parts left if anyone is needing...
  2. BonesBrosChris

    Jeep 2500 Conversion order #2

    I don't know the time frame because I'm not involved with order #3 -Chris
  3. BonesBrosChris

    Jeep 2500 Conversion order #2

    See "Jeep 2500 Conversion order #3"
  4. BonesBrosChris

    Jeep 2500 Conversion Order #3

    The header is really thick fiberglass, fenders are metal (about the thickness of soda cans) everything else is plastic (caps, bumpers ect.) -Chris
  5. BonesBrosChris

    Jeep 2500 Conversion Order #3

    Lots and lots of test fitting...... then lots and lots of sanding. Remember to take some pics. -Chris
  6. BonesBrosChris

    Fitting 2500 front end parts:

    Noted! It does look better with the newer mirrors and power ones to boot! Props to the guys that scored the Rubicon Express Long Arm XJ Kit at the pick-n-pull! You dirty bastards! -Chris
  7. BonesBrosChris

    Fitting 2500 front end parts:

    Well now it's 4wd and has a little bit of lift. I'm going to get the exhaust done tomorrow and after the bed liner. I think I'm done with it for a while. Getting ready to cut the hole for the markers. Sticking on the letters. And out in the street at a buddies house! -Chris Well I still...
  8. BonesBrosChris

    Fitting 2500 front end parts:

    Yes he did. The posts don't interfere with the rubber seal. -Chris
  9. BonesBrosChris

    Fitting 2500 front end parts:

    No mods necessary. When the glass guy came out to do the window he removed all the little plastic clips that the stock metal trim hooked to and put the new rubber seal around the glass and glued it in. -Chris
  10. BonesBrosChris

    Fitting 2500 front end parts:

    Well I got it out on it's maiden voyage this past weekend and it got to see the light for the first time in 6 months. Speedo doesn't work and it's got a rear main leak but other than that everything else checked out good! New glass going in with 97+ rubber seal. -Chris
  11. BonesBrosChris

    Fitting 2500 front end parts:

    Now I feel dumb....... thanks.
  12. BonesBrosChris

    Fitting 2500 front end parts:

    The seats were from an '05 Grand iirc. I bolted them to 97+ XJ sliders and welded in the floor humps (that were also removed from a 97 XJ) to bolt the seats in. The carpet is also from the same XJ. The sunroof was in the truck when I first owned it years ago, so I don't know if it's OE or it was...
  13. BonesBrosChris

    Fitting 2500 front end parts:

    Well I managed to get the headliner redone and the interior buttoned up this weekend. Seems like the weekend is never long enough! Laying on the new material. All glued down. Installed in the truck - And finished installing the sunroof. Grand seats -Chris
  14. BonesBrosChris

    Jeep 2500 Conversion order #2

    And where am I going to post my pictures? jk!
Back
Top