Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Welcome to the new NAXJA Forum!
If your password does not work, please use "Forgot your password?" link on the log-in page.
Please feel free to reach out to [email protected] if we can provide any assistance.
Even though most of you guys have HP D30's, figured I would give this a shot.
I have a low pinion Dana 30 front axle for sale out of a 2001 Jeep Cherokee. It has 68k miles on it and 3.55 gears. It works perfectly and is complete except for brakes/rotors. I swapped it out for another Dana 30...
I got a Amazon giftcard for Christmas and decided that I needed to upgrade my headlights. I ordered an eAutoworks harness to go with my Silverstar sealed beams.
The harness itself is rather cheap looking, much like everyone that has ordered one has noticed. I ran the wiring behind the grille...
I am looking for either a LP or HP complete D30 with 4.10 gearing. This axle must be close to either Lubbock, TX. or Victoria, TX. (so San Antonio is workable).
OR
A set of lightly used LP D30 4.10 gears with carrier would work great too
lemme know!
So after going through quite a bit of trouble to nab an 8.8 with 4.10's, I got the thing installed and it's noisy as hell. The ring gear and spiders looked great when we pulled the cover, and the axle came out of a front wrecked vehicle that "SUPPOSEDLY" had 43k miles on it. And we pulled it...
So, after I annoyed everyone asking questions about the 8.8, it's finally in! It took about 1 week from the time we picked it up until it was in. Would've been a lot quicker but we only worked during the evenings on it. And we live 25 miles from town so parts runs were frequent and extended...
I am getting ready to swap in a 8.8 on my 2001 XJ. I was just looking to clarify a few things:
To my knowledge, I can run this axle with my stock D35 driveshaft and no SYE as long as the lift doesn't cause vibrations, correct? I didn't see a particular reason as to why not as long as I had the...
Like the title says, I'm looking for a Ford 8.8 near Victoria or surrounding areas. I have dug through craigslist and local ads, no luck. I'm hoping you guys have secret sources or friends that are selling some.
Thanks in advance!
(also if anyone is around San Antonio, what does the Pick 'n...
For you guys grabbing shocks from a JK, the steering stabilizer fits our rigs just fine. You just need to source a bolt, 2-3 washers and a matching nut.
Good to know if you have a very worn old factory stabilizer.
And yes, this is first-hand knowledge :D
I am replacing all of my shocks and my steering stabilizer with JK take-offs. The JK steering stabilizer unit doesn't have a bolt on the (track bar?) end where the old unit was pressed in. What can I replace it with? For a visual reference, the bolt I am looking for is the on that comes in this...
This post is for a Grand Cherokee in my town:
For Sale:
Late model, super-charged, Jeep Grand Cherokee 4x4 named: Geronimo. This vehicle has had two owners, a semi-retired dragon slayer and a seventeen-time Grand Champion Jujitsu Master. A very sleek and sophisticated automobile machine...
Has anyone else seen the CB mount that Jeepoutfitters.com has for the TJ? It puts the radio in a pretty sweet little spot.
http://www.jeepoutfitter.com/cb-radio-c-228/mp-jeep-cb-mount-bracket-mini-cb-tj-p-749
I know our 97-01 dash is pretty similar to the TJ's. Would this fit our XJ's?
Just...
So I have this innovation project that started yesterday. I have 3 other teammates, and the project is due in 2 weeks.
Basically, this project is for an entrepreneurship class. We have to make as much money as possible in the 2 weeks.
Here is the criteria:
We can only use $5 in cash.
It...
So this may have been covered...and covered...and covered some more.
BUT! I am looking for builds that have 3-3.5'' of lift, with things like:
Upgraded U-joints
Aftermarket diff covers
Extended breather lines
Rock rails (or whatever you choose to call them)
Skid plates
Full poly (or something...
Yeah I know the title was vague. I am looking for anything to improve my '01 XJ. I have a 2.5'' BB. That's it. I have a limited budget.
Show me your cast-offs, old bumpers, lift springs, etc.
And even though I have a limited budget, I won't lowball :-)
Thanks in advance for your help and time...
I realize that sounds are hard to hear over the 'net, but I was hoping you guys could help me diagnose a few things:
Whenever I accelerate from a dead stop, I get a sort of chirping/squealing noise whenever the jeep isn't warmed up. I am thinking this also has something to do with the lurching...
http://lubbock.craigslist.org/cto/1567606568.html
1978 Jeep Cherokee Full Size Jeep Widetrack FSJ WT
Runs good. 2 door, 360 T18 D44s
Great for hunting lease
A little dirty from sitting in storage
$1,600 OBO
575 390 8438
(not mine, nor anyone I know. Just thought it was kinda cool)...
Ok, I realize this probably isn't the smartest question. Just curious though.
Is there a way to put a switch inline to the passenger airbag to have the ability to turn it on/off? Without causing lights to come on. Also, without having to due any crazy engineering/modding.
The reason I am...
All of the XJ's (and I mean ALL of them) I have seen in Lubbock and in Victoria TX. have ChryCo 8.25's in the back. Not crying about it, but why did I buy the one XJ in Texas with a 35? :gonnablow
Just waiting on someone to wreck one here in Lubbock so I can pick up a cheap axle upgrade. Or...
Before anyone says anything, I HAVE searched, I promise :cool:
My '01 has a cracked coolant overflow tank. I have melted it together, covered in JB Weld, etc., with no help. It leaks about half the tank a day.
Is there any suitable swaps from another vehicle that would work? Or any aftermarket...