Search results

I got this trans off CL and I was wondering if this is the oem type of pan sealant they used. Maybe never had the pan off. The fluid was dark but didnt smell bad. The seller said it was a higher mileage trans but was working good when removed. My original trans has 620,000 miles on it so I got...

I got a used tranny and while checking it out, when I pulled the conv. out and being full of fluid I shook it back and forth. That's when I heard the clunking noise. Just wondering if thats normal, the clutches moving around or something. Also the fluid that came out was pretty dark but didnt...

How much movement if any should I have when pulling on my front d/s out of then into the tcase. Mine moves 3/16 of an inch. Normal?

Sometime ago I replaced my ball joints. Now as i trace down a wonky steering I am seeing the bottom ball joint nut turning when I turn the steering wheel. Is this correct or is the joint bad and the big bottom nut should stay straight ahead as knuckle turns left and right.

The last new one I bought 6 months ago before smog test was an all metal style. It just quit on me after 6 months. Maybe last week at Anza Borrego high temps under the hood killed. But it shouldn't have. Any of those metal body o2's are junk, every time I end up putting my spare ceramic body...

My 1989 4.0 FSM says 2.0lbs of r12 for charge amount. Ok, so r134a amount is 2.0 x .90 - (.25lb.) = 1.55 lbs. according to online conversion charts. But on a Comanche forum I saw a FSB No:24-01-95 that shows 38 oz./2.38lbs r134a refrigerant charge for 88-90 xj 4.0 What's the real refill...

Anybody have an idea where I can locate a lower Speedo cable? Rock auto has one but it's 90 inches and both cables added up on mine is only 78 inches to gauge from these. Has anyone used that 90 inches with success I will bypass C.Control if I have to. Thanks

https://photos.google.com/album/AF1QipMLOHgXeUlQJQhDfKbN_cnZjJtrQjKGO2NKrDpO/photo/AF1QipMDtGFxkdFPdpIg9sXhESNjegM176spF3QWnjOm My daily driver with original engine and transmission https://photos.google.com/photo/AF1QipO4aCAHPdSkU52rjWOW-fy18awsFA933V5ffQzV

With my dvom back probing 3 wire connector, key off, extra ground hooked up . I read less than 1ohm, Koeo ,reads 1ohm. When I remove extra ground at this point(stock configuration) it reads 9ohms. Is the 9ohms coming from the ECU? It must be, and is 9ohms anything to be concerned about? I...

I'm having a high idle problem and trying to rule out the usual suspects and noticed the throttle shaft has a little side to side play. Anyone ever have to mess with rebushing the t-body like they do a carb. butterfly? could vacuum be leaking slightly thru the shaft bushing? 89 renix

How do I repair this? Both sides are buckled at the wheel arch sheet metal.

The fsm wiring diagram shows a circuit breaker between B1 and H terminal on headlamp switch body. My headlamps are going on and off and im trying to narrow down my troubleshooting as it is a sucker to access the switch and connector under the dash and test when failing:smsoap:

Need to swap my 89 D35 Trac local 3:55 gears for a jy unit from a 1990. Any problems with this swap. And can I use any year axle D35 with 3:55 gears?

Wheel off and jack stand under axle, I can lift hub/knuckle up 1/4" pretty easily. Sound correct to you guys?

I was in Anza Borrego this weekend and after climbing a long trail that got my temp past 230* . I let it cool a bit and turning the key, the fuel pump was growling bad. No start. Dam. After the usual checks, tried again. Growling pump and No Start. Now I'm in trouble! 110* out, backwoods...

So my 89 started making a buzz sound with key on engine off. With the old hose to the ear sound detector trick, I traced it to the alt. Now, I got a back up alt. and unhooked the suspect unit and hooked up other alt. (on top of valve cover not installed). Turned the key on and when alt. case...

Any thoughts on this shell out of rear main cap?

At freeway speeds under moderate throttle I get a noticeable ping. My knock sensor has been out for years and just passed smog. Only change was a new Felpro blue valve cover gasket. My scanner reads good head Temps with ECT relocated to the stat housing, so I'm stumped on the cause of my...

My t-housing keeps leaking with a new gasket. thinking of using RTV only. What do you think? The gaskets have a glue on one side like a sticker and that just aint sealing it well. I have even sanded the housing flat to remove low spots from corrosion and still leaks.

I was troubleshooting the ccv by blocking the hose at air cleaner and pumping air in at rear vacuum hose to see what was leaking. So I forgot to unblock freshair hose and drove to work like that. Had my mt 2500 hooked up at the time and saw it staying in openloop all the time. So when I got...