Search results

I believe these are all the same. Mine is a 94. I need the transmission pan. Mines bent and doesn't seal very well.

I picked up a 94 XJ 4.0 4x4 auto awhile back and recently got a lift installed. When I got it back from the shop the emergency flashers won't shut off. The switch on the column is off and the lights on the dashboard don't light up but the turn signals do and you can hear the clicking. Dash...

Looking to make an offer on a vacant piece of land. Need someone with some knowledge to look over the contract/offer.

My sons 89 MJ blew the front wheel bearings, welded it to the spindle. Tried to get it off and no go. Its in a parking lot on Pendleton. would like to get the whole assembly - spindle, knuckle what ever else so we can just unbolt the knuckle and put the new one on with his old hub/rotor. We...

My son was trying to fix his oil filter adapter leak and ended up stripping the threads on the piece that the filter screws onto. So does anyone have a spare adapter? Its a 4.0 Renix 1989.

I know its supposed to rain later this week, but I just bought a new Ram Power Wagon and want to test it out a little. I have never been up Cleghorn and wondered if anyone wants to try it with me? I've got 37" BFG mud terrains, locked f/r and a winch. Or any other suggestions for a close...

This is all out of my 1980 Cherokee - had it running a couple of years ago, ran out of gas and it sat. Only drove it about 6 miles. It will need new vacuum lines since the old ones were in bad shape, but otherwise its complete. New starter, new mechanical fuel pump, carb (motorcraft 2150) was...

Anybody have any experience with Pomona Gear? http://www.pomonagear.com/ Looking for a reputable shop to do an engine swap. I saw an article where they did almost the exact thing I am looking for. Going to talk to them this week, just looking for some feedback.

Looking for someone to work on my full size Cherokee. Im working alot of overtime so no time to work on my stuff. I need the engine/trans/t-case removed. I would greatly prefer if you had your own hand tools. I have engine hoist/stand, air compressor, jack stands and a couple of jacks. If...

Looking for a Comanche somewhat local to Socal. This is for my son so no high end stuff, just a solid, pretty rust free MJ Been looking at Craigslist, anyone else seen any?

Redlands to San Bernardino about 12 miles Full size Cherokee on 40's and tons. about 6000 lbs or so, doesn't run but I can pull it onto your trailer Anyone?

Anyone got some spare parking spaces, preferably behind a locked gate/fence around Redlands/Loma Linda area? Would like three but would settle for two regular sized spots.

Someplace close to Redlands/Loma Linda. I have my FSJ Cherokee and another car that both need work, no fabrication just normal stuff. Carb tuning,some suspention work, exhaust, and more. I live in an apartment and landlord frowns upon oil changes and such. I would like to find a place that...

I need some help tomorrow. There is a rear axle (AMC 20) in a salvage yard in Rialto that I need for my full size Cherokee that I bought. I recently moved to California and don't have access to all my tools and no truck either. I need some one with tools and a truck to give me a hand pulling...

I have one pair of rear Dana 44 stock axle shafts, complete with bearings and seals, ready to put in. Located in Loma Linda CA, $150 for the pair obo

one pair of Dana 44 axle shafts, complete with bearings and seals, ready to pop in place. I already have them boxed up and ready to ship $100 plus shipping from 87410 Aztec NM.

I have been searching but can't hit the right words in my search. 88 MJ with a 4.6 stroker - all sensors/external stuff is stock 4.0 stuff. I have had it sitting for a while and charged the battery up and got it to run. Went to shut it down and does not stop? Can pull the key out and it...

In case you haven't seen the for sale ad over in the intermountain chapter: http://www.naxja.org/forum/showthread.php?t=1025893 I am willing to deliver to the Pueblo area if paid in full before.

Located in Aztec NM but I am willing to deliver to Flagstaff if asking price is paid in full. $4000 firm! here is the ad : http://www.naxja.org/forum/showthread.php?t=1025893

Selling my 88 long bed MJ Located in Aztec NM, NW corner of NM. Asking $4500, delivery possible 4.6 stroker engine, about 40,000 miles on it, 24lbs/hr Ford injectors, double roller timing chain, stainless steel exhaust, NEW head and hardware (valves, pushrods etc.), everything was replaced...