Search results

I am having some difficulty getting the holes on my upper control arm to line up. I had them out to change the bushings. I thought that by doing one at a time and leaving one connected, there would not be issues. The axle rotated forward when the old one was disconnected. Both are stock control...

I saw an unusual xj today, it was tan with a little black, on 33s, and the back was chopped. Ok, so that isn't so unusual, the odd thing was that the driver had what looked like a boa constrictor around his neck! and also the hitch was a velociraptor.

My 88 with the 4L will crank over but not start, just like the cps or ckps is out. It has been doing this for almost a year now, steadily getting worse, but after I replaced to cps I thought I fixed it. I can hear my fuel pump prime and there is pressure at the rail. I have tried: New...

On an 88 renix, I am having distributor disassembly issues. How are you guys driving out the roll pin that holes the gear piece to the shaft? I’m like 100% sure that that is how it is supposed to come apart, but short of being far more brutal than I want to be with an expensive aluminum part, I...

http://www.recordnet.com/apps/pbcs.dll/article?AID=/20091215/A_NEWS/912159983 http://www.recordnet.com/apps/pbcs.dll/article?AID=/20091220/A_NEWS/912200323 they are worried about soil erosion in a dry creek :flamemad:

This made me decide that I do need a gun. So basicly unless you have a special deal going on where they say they will protect you, they dont have to do shit! And according to this gem... Calling the cops multiple times telling them that you have been threatened isn't enough The whole...

Osama bin Laden found! Turns out he was hiding in the attic the whole time!

Ok, so I really screwed the pooch this time. :doh: I was changing my cps. It is a tight fit in there for a hand, and the bolt was greasy, it wasn’t really well lit, and basically, I’m just making excuses. I dropped my cps bolt IN the hole of the bell housing. :twak: I have dug around in the...

I am wondering if the pinion flange from a d35 will fit on a d44. I know I read somewhere that one would fit the other, but I would rather trust naxja then a fuzzy memory. :confused1

I ended up building a crossmember for a few reasons. 1. I wanted a strong one to mount my skid plates off of. 2. I wanted more ground clearance. 3. My old one was dented up pretty bad. 4. I will never buy anything I think I can build. My old crossmember; First I took out the studs and...

I have a Chrysler 8.25 axle, I’m not sure what year it is, but it’s a 27 spline. I bought it as an upgrade for my d35, but a week or so later, I ended up with a d44. I would like $40, but make me an offer.

http://blog.wired.com/cars/2008/07/blowing-up-a-60.html?npu=1&mbid=yhp dumbass.

Hypothetically, Say you have an alternator that will pass an alternator machine test, but when under load wont put out the voltage needed. with the lights on it wont charge and will sometimes discharge! The store wont replace it under warranty because it passes on the machine, but it is nowhere...

I have been planning out a paint job in the future, and asking people for ideas. When people explained their ideas i had a hard time telling what the hell they were describing. So i spent aproximatly 1 billion hours drawing this from memory in ms paint. Yeah i know its not 100% accurate, but...

I have a few sets of these, a couple different colors too. $40. $30 if you are red.

I have a set of the Chevy brake lines everybody else seems too have, for the c1500 truck. How is everybody getting those brackets off the middle? It’s a pain in the ass! I’m scared I will cut them, stab them etc.

I have a np203 transfercase. It was behind a th400, but i dont have the adapter. Its not really a jeep part but people put them in jeeps. I am tired of it sitting in the garage and i want to get rid of it. cost; you have to help me pick it up when we load it in your truck. Its pretty heavy.

http://youtube.com/watch?v=wKsoXHYICqU she could convince me to vote

check out what this little kid does in a sand rail http://youtube.com/watch?v=31z6UswHb_w

I am making a new crossmember and have a few questions. while searching i found this post http://www.naxja.org/forum/showpost.php?p=701578&postcount=17 this is my idea Basicly make the mounting plates stick forward and back a couple inches, and put some self tapping screws in there. i figured...