Search results

Quick ? I just got a lockrite for my d30, and it's unusually loud. It kind of sounds like it's binding up, then it has a really loud pop. Both tires are getting traction, right after the pop. Thing is, it's kind of hit and miss. This auto locker is used, but I don't see how anything could be...

I replaced my axleshafts with those out of a 06 TJ. I did this to gain some strength with the 297 joints. I also did this to get rid of the CAD. The problem is the passenger side shaft is not sealed up. It is leaking a small amount of gear oil out of the side. Anyone know of a seal I can use to...

Last night I replaced my axleshafts and hubs with a set off an 06' TJ Unlimited. I did this to gain U-Joint strength, since the TJ's have the 297's. I also did this so I could get rid of the CAD and the two piece longshaft. I used the rotors off the TJ also, they sit differently than the ones on...

hey guys, i have a AW4 that i got from a buddy of mine. he isn't sure if it's in working condition. is there any way i could find out, without mounting it up and trying it out? i'd like to use it someday maybe as a full swap into a yj (RNX 4.0 + AW4). i figure i'd need to drain it and have it...

can anyone explain to me why you have to mark the positions of the ring gear on the carrier, whenever you remove the carrier from the differential? also, what is the importance of making sure that the thrust washers and bearing caps go back in the same spots as they were in, for example if you...

Just wondering if anyone lives near Uvalde, Tx or if anyone has even heard of it. I feel like i'm completely isolated from the world. 1987 XJ 4.0 AW4 231 D44 Chopped + 4" Topless

Hey guys, i'm in the process of capping off the line that runs from the gastank to the charcoal canister. I've read that a few of you have done it. I followed the metal line along the frame rail and at the rear of the vehicle it turns into two separate rubber lines, one on each side of the tank...

I am in the process of taking out whatever I possibly can to clean out the engine bay of clutter. Right now i'm trying to figure out if it's okay to pull the "football" (vaccum canister), and the charcoal canister. I pulled the football earlier and it's running fine. There is a line that runs to...

anybody going out to katemcy rocks on june 13 and 14? a buddy of mine was telling me that they're going to be closing soon after that. i've never been there, so i'm thinking about going with two of my friends for the first/last time. my xj isn't ready for the voyage, so if i go i'm taking my DD LJ.

Hey guys, I really screwed up. I recently had the renix "brown wire" issue. It burnt up a bunch of my wires. Some weird voice told me to just wire in a fresh harness, so I did. I have a parts jeep, of the same year (1987). I disconnected everything under the dash. and seperated the harness where...

Hey guys, my 87 XJ started messing up about a week ago. What i've checked: Wiring Fuses Flashers What works: headlights-both hi and lo hazards What doesn't: wipers turn signals I'm either narrowing it down to a bad switch or a bad ground somewhere. The left green arrow stays steadily lit...

I read this on JPMag's website, is this some kind of sick joke? An old April fools story? Or is it real? I typed in "International Jeep Corporation" on my search engine and turned up nothing. International Buys Jeep Real Jeeps On The Horizon By Pete Trasborg Amidst all this economical doom...

I'm thinking about getting this for my GF, but from what i've read so far I have a feeling it might be a cracked head or the head gasket. I did a search and now also think that it may just need a burp. I know it's better to go look at it in person, but it's kind of far and I want to know if it's...

This question is for Renix-era jeeps. My Question : Do any of you all know what wires go connected to the battery, by factory standards. My - only had the - ground connected to it, but my + has the + battery cable plus the medium thick wire that goes to the solenoid near the relay block plus...

I'm selling a 1987 Jeep Renix Engine. The engine is currently still in the jeep, so I advise anyone who's interested to hear it run before they buy it. I've never pulled an engine out of a vehicle, for one I don't have a cherry picker and I don't have the time. I would like for the buyer to...

Hey guys, I thought I'd offer some stuff to you all that's taking up my space. I've used NAXJA countless times to help me fix my XJ, so i'm going to give back. All of this stuff is free to all of you all, but i'm going to try and get a few bucks off of this stuff on craigslist. XJ Doors 84-96...

hey guys, in my process of trying to convert my a/c to oba, i messed something up. I was trying to grind down those "ears on the top" originally two hose mounts are bolted to them. my grinder accidentally struck the output ports threading and i kinda freaked, so i tried putting my 90 degree...

Hey guys, I was wondering if anyone could give me some ideas on how to fix my throttle cable, or if that's even the problem. I tried searching for a fix, but couldn't turn up what I needed. My throttle will sometimes get stuck whenever I floor it, I can slow the jeep down by holding my brake...

Hey fellas, I did a little bit of searching but I couldn't find exactly what i'm looking for. I know alot of people have done H.O's into Renix XJ's, but I was thinking about putting a Renix into an H.O. I found a great deal on craigslist for a 96 2 Door, body is in real good shape but it says...

hey guys i was wondering if anyone could give me some pointers. my jeep has a dana 44 3.73 with the trac-lok (limited slip). the other day i was way off camber, and my left rear wheel was slightly off of the ground. in 4lo, i would give it a little gas, but my right rear never gave me any...