Search results

I don't post much... I can find 10x answers via search. This has me stumped. 1. 1989 MJ 2. 89 Renix 4.6 Stroker 3. 94? AW4 Auto (swapped from ax-15) 4. NP 231 Problem: When the Tranny was bolted up tight, and the engine was installed, I could not get the engine to turn over. I had the 89 all...

Folks: I bought an XJ to strip for parts while I'm rebuilding my MJ. It ran awful when I got it from the son who got it from his dad's estate. Before I got into it, (IE stripping it) I wanted to know if the motor had any potential for resale. Turns out when the son got it, he had it serviced...

I did a search, and no one addresses this issue head on... If the answer comes back as I fear it will... I'm going to be pissed. I just bought a PORC SYE Kit. I have an 89 MJ/ AX-15/231J. I have the right kit. I know that I am supposed to cut the slide rod for the shifter. Here is the rub...

OK... Here goes... 1. Foam & Rubber firewall mat in good condition. (No Non-OEM holes or rips) 2. Passenger side vent window (not a fixed pane, a vent pane) 3. Power everything door wiring harnesses. - I am adding power windows, locks, and mirrors, I need the wiring harnesses that plug in...

I am looking for an Adj. Track bar - Prefer Rustys with the replacable Tie rod end. I only have a 3" lift, so I don't need HD. I keep looing in the for sale section, but I always seem to be the SECOND guy that sees it posted. just not fast enough I guess. If you reply to [email protected], I...

So the MJ truck is going together, and I was planning on doing dual electric fans. I have a new 2 core modine, 4.6 stroker, and a renix setup. I have the older style aux fan, and recently purchased a 19115 perma-cool. The perma cool is not going to work, as there is not enough depth, and I don't...

First, let me say that I don't post until I have searched. I either become well educated or well confused. In this case I am a little of both. I have an 89 block with renix electronics. I have a 0630 head, with the newer (91+ I think) water neck. I am building htis truck from the ground up...

OK... so this post is really only for people searching. There is no need for everyone to chime in to tell me I'm an idiot. In my defense, the truck (89 MJ) was torn down to bare metal, and then sat for 1.5 years before I got to get back to work on it, so I can't be expected to know where...

I don't know if I can post this here, but I thought I would try and get censored if not. I want to reccommend a vendor for 24lb injectors (ford) - to those building a stroker - especially a budget one. I am NOT connected with this vendor in ANY way, other than I tried to buy injectors from him...

BCS CHAMPS! :)

Does anybody have a short throw like the one summit offers? What are your opions? It's going is a longbed stroker. Thanks.

Did a search - no luck... I am a dingus (pronounced Ding-gus). I seem to have lost my stock pushrods. I am building a stroker, and I need new rods anyway (stroker motor) but I don't know the original specs for diameter, end type, etc. I THINK it is a 5/16" tube iwth ball ends and no oil holes...

I figure there is something that I just don't understand here... OBD code 33 (there is NO relay in the AC relay spot)... Here's what we got... 92 MJ, 2.5L, manual Starts and runs... When it warms up for 10 minutes the MJ stalls out. The voltage at the battery drops... 14, 11, 9, 5 volts... WTF...

OK this should be an easy one. I don't have my stock pushrods. (They are at home) and I want to order them asap. What is the stock length of push rod? I have stroked the block, and in the process I decked the block and milled the head, so I will take that into consideration when I place the...

Hi All... YES I did a search. I have found info on what people are over/under for clearance, but NOT the actual clearances per the FSM. I am going to be checking the specs for bearing clearances - installing a new crank & bearings for a stroker build-up. I don't have a FSM (STUPID ME) and I...

I am doing a stroker build up... I am looking for a pan in great condition, or maybe a source to buy a new one cheap? I am running out of money FAST. -- located in Maine (Newport)

I am doing some calcs for a stroker... I'm using the ever popular "AndreasStrokerCalc.xls" from MadXJ. I am wondering what is the maximum material that can be removed from the 242? I was thinking of having mine decked, to bring the numbers back around to 9.69:1 with a quench of 0.0635... to do...

I need help and I am hoping some of the gurus (like Eagle) can help me out... The question is about a DANA 30. I am not a newbie, perse... I have no reason to upgrade to a 44 on this project, as this one will probably never see a trail. It's a pavement pounder. I am stumped. I HAVE SEARCHED...

I am rebuilding a comanche from the ground up. I am having a problem locating the mounting bolt for the heaterbox. The car is stripped of everything else. There are bolts inside the engine compartment that MAY remove the box, but right now they spin freely. Are these 6? (I think there are 6)...