Search results

my junk is stumbling at random, as if the distributor is being dunked in the water, like a flat miss, at random, and if i floor it, its gotten better through out the day, i may have gotten the radiator wet when i did my cooling flush this morning, but i pulled cap wiped em oth clean then lightly...

So im heading to tahoe for the weekend, wanting to see if anybodys up for a day trip to the con on saturday?anybody else already have something planned i could join in on? im on 35's front locked,rear open.

ok posting for a friend, 89 4wd 4.0 auto, the check engine light wont turn on at start up, causing him to fail smog...i searched.where should we start? what controls the light to turn on during start up?

with xj brackets and 4.10s...help!!! Ricky 510 676 6695

Ok I give up how do I get these off worked it self loose, I bust one of the Torx bolt on hatch side. It rattles it's annoying help.

so i put in my new to me AMC20 today, before you say amc 20 wtf look at the thread i posted when i intially purchased it, http://naxja.org/forum/showthread.php?t=1008920. so while re-assembling i snapped off a ujoint strap bolt in the yoke, crap so i drilled it out and smacked in a kd tools...

So im purchasing a welder some time in the next week, im looking at the hobart 140 and lincoln 140, any opinions?

so today,im going to dmv to get my OR license, and plates, now exactly what are they going to test on my truck, i know theyll make sure theres one vin, but as of right now, my blinkers arent working....and i cant trouble shoot it, are they going to test? and how stingent on mud flaps are they...

got these today for 10 bucks including shackle's(shackles are 6.5 long) and they measure 24/cp/32, has any one ever just slapped some in? Im installing the amc20 i got soon so i can move the cp hole an inch back on the perch and be centered, think 4 inchs longer is to much for decent shackle...

so i had to buy it(20 bucks and a 12 pack), came out of an 86 comanche, so i know its got the right width and bolt pattern and....open 4.10s. from what i gather about this axle is it is MUCH better then the the two piece axle shaft CJ counter-part.it has 8 7/8 ring gear, 29 spline one peice...

Do you have 5.5-6.5 in of lift with re or similar long arms? Can you effectively use a tape measure? Got 20 minutes to spare you should pm me your number or vise versa thanks Rick

so, in Winchester bay this weekend my truck started getting hot opening it up in the rhythm sections doing at 40, hmm ok weird do the usual open hood and look, to see my coolant bottle surging big then small soo, bust out the coolant jug of water i got and proceed to dump into front of radiator...

Where is some good camping up there cheaper is better, goin tomorrow will I need fire permits? Where can I get camping, sand tags and said fire permits . Thanks!

I must say out of all the aftermarket products i have bought, Rory has had the best customer service, even answering my calls at weird times willing and politely answering my questions, ordered my shifter on friday, its here today(monday). i have it installed now and it works fantastic, recently...

So im trying to figure out what my pays going to be, so i can figure out what range of rent i can afford, il be making 10 an hour 40 hours a week, im claiming single, zero. some one help i cant find any calculators online(dial up doesnt help)

just noticed p side upper is sheered, how safe is it to drive on? no junk yards around, im short on cash as it is, canman is shipping one to me, but i need to know if its half way safe to run just one stock upper? atleast until i get the one from canman in the mail

so about two days ago, my truck started studdering like a flat constant miss, stumbling like i was runnning out of gas and even has an intake back fire once or twice. then for what ever reason it will start chugging like usual also two days before that i hooked up a home made intake tube and...

so, went to go finish some wiring under the truck, noticed two cracks on the p side upper, at the axle end, about 2-3 inches from the mounting holes. What do i do?there the factory arms, In all honesty i cannot afford to buy some uppers right now, and this is my dd, think it will accept a weld...

In all honesty what do you guys have into your dana 30 $$ wise,im trying to weigh out just getting a HP44 cost to just beefing the snot outa my 30, this is my dd, but ive got alot of down time. im getting ready to make the swap from my 33's to 35's, i have rims for any pattern so thats not a...

So i moved here about 2 and a half weeks ago, nice town, sucks really bad to be a twenty year old here. More so im wanting to find out, where is the best place to get steel around here? Also where are there some decent trails? And how do i go about finding out who owns what land, i was exploring...