Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Welcome to the new NAXJA Forum!
If your password does not work, please use "Forgot your password?" link on the log-in page.
Please feel free to reach out to [email protected] if we can provide any assistance.
Does anyone have experience with a Dana 50 under their XJ? I can pick one up that has been retubed with .25 inch tube for probably $250. I have searched for bigger axle shafts 35 spline it looks like it’s possible but not a lot of info out there for showing experience with swapping this axle...
Had my jeep weighed on the scales at the dump. It was unloaded and came in at 4,800lbs. I had it weighed twice and both times it was the same. What do your XJ’s weigh? Do you think 4,800 is to much? I think I need to go on a diet.
Does anyone make Aluminum fender flares or Fenders? I need some flares but don’t want to ad weight. I am considering fiberglass fenders but I could crack them on rocks l mostly wheel Tahoe National Forest.
I need to buy a new bumper since my Warn M8000S winch I purchased won’t fit my ARB bumper. I have looked at a few but was thinking I have probably not looked at all my options. Do we have a list out there?
Happy Thanksgiving everyone and thank you for reading my post. My XJ has a GVW of 4,800 pounds unloaded. I have an ARB front bumper and my winch options are the M8000 or XD9000. There is a significant price difference between the two and I was wondering if the M8000 would be sufficient enough...
I have a roll cage in my 2000 XJ and am looking for ideas on how to install harnesses using my stock seats. I searched to see if anyone has modified their stock seats for harness set up and have not found anything. I was thinking of cutting pass through holes in the seat to snap in side by side...
3 years ago I had a no bus code on my instrument cluster and swapped it out with one from the junk yard. Since then I have had no problems until today. As of today I have no bus code and I own of the gauges are working, the check engine light is on, air bag light is on but the lights and...
I have a 6” long arm Full Traction lift. The rear sits low and their web site says the shackles that come with the 6” lift add 1” lift over stock. I don’t want to change the springs so was thinking of getting longer shackles. Does anyone have recommendations I need an additional 2” of lift so...
I just got my Jeep out of the shop I had it in for several issues one was high idle. My idle is around 1500 when in neutral or 1000 when In drive. The shop lubricated the cable cleaned the throttle body and cleaned the Mass airflow sensor. The high idle does not happen until the engine gets heat...
Why is pricing all over the board for fuel injectors? I see them for as low as 19.99 for a set of six and as high as $230.00 for one. I replaced all of mine today bought them from Napa 555.00 each they are one hole injectors made by Echlin. I was not sure what brand was good so just went with NAPA.
When I purchased this cage I could not find a lot of documentation on install from consumers so I have decided to post my experience with D&C and installing their cage into my 2000 Jeep Cherokee Sport. Fist off I would like to say that the employees answered the phone every time I called them...
I am going to start my D&C cage install and was wondering what type of welding wire I should use for the floor plates and cage. I am using a Miller 180 with 75/25 mix. Any pointers would be appreciated it's my first cage install.
Thank you.
So I have a LP Dana 30 that gets abused a lot and want to upgrade. I have a Currie Rock Jock Sterring system that I would like to use on the replacement axle. The axles that I have been considering are Dana 60 F250 or 350 HP ball joint, Dana 44 ford HP and Dana 44 Wagoneer non vacuume disco LP...
Back in August of 2016 I took my XJ on Barret Lake Trail with my friend who has a cruiser. On the way up the Hwy about an hour into the drive the XJ started back firing and shut down at 70 MPH and I had to pull over. I tried starting the XJ but it would not start just turned over and over. I...
Does anyone have experience with 27 spline RCV shafts in their Dana 30? I have the Warn hub conversion with Crome shafts and a Trutrac and was wondering if I could use the RCV shaft with the Warn hubs and if they would hold up to 35's or even 37's.
Hi,
I can't post and have net been able to post since my credit card changed and my membership was canceled. Would it be possible to fix my profile so I can post?
Thank you.
I need to align my front axle and have a 6 inch FT lift. Can anyone give me an eye to eye measurement on the lowers and uppers to get me in the ball park?
Thanks.
I have a 6 inch lift and need to adjust the lower and upper arms as they are out of whack. What is the best way to center the front axle left to right and front to back? It looks like my axle is to far forward and the pinion is pointing down to much. I will be replacing hiems and Johnny joints...
I have a 6 inch full traction long arm kit and would like to put metal cloak bushings in the lower control arms currently the lower control arms have Johnny joint in them and is from the first full traction 6 inch lift kit that was made for the XJ. Has anyone done this and if so what size Metal...