Search results

I have a HP.D30 housing that's been sitting open to the weather for some time. Some surface rust has appeared on the inside/bearing side of the carrier bearing caps. Are they trashed or can you clean them up with some sand paper and still use the housing?

2001 Automatic Driving home from work yesterday morning, -4° , my rig started running a little rough and the check engine light started flashing. At this point it started limiting rpm's at 3000. Three codes came up on the scanner. Gross evap leak (that I've been trying to chase down for a...

Probably an easy question, I'm thinking thermostat... My 01 runs a little too warm in summer, 230 degrees on a pull and won't get over 200 degrees in winter. This makes for a chilly ride. Brrrr... It will warm up somewhat while sitting at idle or on a long hard pull. Everything sans heater...

Crossfit addiction ... Never thought it would happen to me. Anyone else?

First, since I'm asking about a non factory item I posted in modified. If that's wrong please move to appropriate forum. When using a remote start what all comes on with the engine? Are all accessories are armed same as if you used a key? Or does the engine run sans anything else? The...

The hole(s) on my front able where the track bar mounts are wallowed out pretty bad. What is the best way to effect a repair? I'm thinking off plug welding the old hole and drilling a new one.

My current springs are shot so I'm going to replace with 'RE 3.5" coils. For sake of ride quality I want to use LCA drop brackets. Expo, camping rig, mall crawler... I already have 'RE adj. LCA's. Will I also need new adjustable uppers to correct castor and wheelbase?

I just can't bring myself to spend more money on seats. But I'm not the best welder and fabricator. If you have pics of your seat frame, not riser, repair I'd sure love to see them.

I'm posting this in Modified since the seats are an aftermarket part. So at 6'2" and anywhere from 245 to 325 lbs depending on the year I'm hard on the XJ seats. I've done the ZJ swap and don't care for the increase in height and of course, being a lard ass, I've blown out the frames on those...

Hey I got my NREMT-Ambulance certification back in 88 and got one of the old school EMT-Ambulance patches with rocker on top and on bottom. I have torn my house, my shed and my parents place up looking for this old patch so I can put it on the wall beside my new EMT-I/99 patch. If anyone...

Yes, yet another coolant thread. I can't find a thread with my specific combination of problems and I don't know if they are related or not. I would truly appreciate some experienced opinions. System specs: All components less than two years old, most less than 12 months Runs in the 195* to...

Have no idea which is the appropriate sub forum for this question, so it's here. Looking for those with "experience" with this issue. I live 2000 feet above the Roanoke Valley. Often, I don't drive through fog on the way down the mountain as much as I drive through low lying clouds. Common...

I searched and got nadda. 2001 auto Temps running between 195 and 205. My heater blows tepid,80*, at the center vent. Cooler in cold weather, hotter on modetate temp days. On a long pull ot will heat up nicely. I noticed tonight as the Jeep was warming up, with the heater going full blast...

I have a 10/22 that I've mainly used for plinking over the years. I am now having some serious raccoon issues and I see this as the perfect excuse to upgrade the old Ruger. So, for night shooting varmints (legal on my own property, no nearby neighbors. It's all well and legal I assure you)...

Yeah, so never ask me to install speakers... Need a grey driver side front door panel in or near Roanoke VA. Looking for free or close to it so as to save me a trip to the JY.

My mileage has been all over the place this summer. And it's the first summer I've had AC in a few years. Right now I'm bouncing between 14.5 and 16.5 uncorrected. These are measured at fillup with no real change in driving habits. All fill ups at the same gas station etc etc. (I'm trying...

New parts on front end: TREs Double shear track bar Adjustable LCAs Tie rod Both hubs Upper and lower ball joints Steering stabilizer Shocks Everything is torqued to spec. Axle is not centered I have to adjust the track bar Toe in set to 1/16" This thing steers tight as hell. But when I...

Where can I find the CFM numbers on the stock 2001 XJ mechanical fan? Have an argument going on with my non Jeep engineer know it all buddy and he won't accept forum threads as a credible source of information. Yes I've googled but come up with page after page of forum threads.

My torque app reads engine temp 20* or more warmer than my temp gauge. But only after it gets to 210* . Before that they march. Any if you running this app noticed any descrepencies?

My 01 has a 2.5 or 3 inch lift. I can't remember which. The rear stands as tall as it ever has but the front has started to sag and I've added a winch bumper which has made it worse. I'm adding a winch before the snow hits and am pretty sure that will be a good time to upgrade coils and...