Search results

This is my third xj build. First one was a complete bolt on credit card jeep way back in 2006 with a Clayton 8" longarm and 35's. Jeep was fun, and i became hooked: In 2008-2009 i built my next one. One tons, atlas, 14" fox coilovers, stretched, caged, full hydro steering, originally on 39"...

I posted this in modified because the jeep is highly modified, and i am at the end of this damn build and ready to go and am having some last minute issues. First major thing is the gauge cluster does not work at all. I have lights, dimmer, idiot lights, but no gauges, and no odometer. I have...

Is the sound that is coming from the bottom of the tranny. I have pulled the cover and tightened the hell out of the flex plate bolts, and visually checked for cracks. It cannot be the exhaust, or the tcase. What else in there could make this sound. It only does it when i am at hard flex, or...

Installed lockrite and 4:88's in a hp30....my last one i had in the other jeep just ratcheted around sharp turns, nothing ridiculous, this one pops loud, about every 5 feet when making small turns, and gets way worse on tight turns, all in 2wd. The locker works in 4wd, but i dont think its...

Ok, the last thing i got. Clayton long arm lift, approximitly 1 year old. Comes with the following: complete sway bar, with jks quicker disco's rock krawler hd trac bar and bracket front 8 inch rock krawler coils stainless brake lines Long travel rock krawler shocks clayton long arms...

this is located in summersville wv please pm me here, or email me at [email protected] thanks for looking here is everything that is for sale: built 8.8, front hp d30 and np231 ford 8.8 out of 99 exploder 31 spline stock shafts yukon 4:88 gear full detroit locker homeade truss welded...

Ok, thought it was the uppercontrol arm mounts and bushings, so i bought the tnt truss, put it on, ever thing is tight. When i back up my camber goes negative, its not the tires either. I have pushed and pulled on everything, no movement. Balljoints seem fine, and the hub bearings seem tight...

Ok, i searched and searched........and nothing. When i back up, my camber goes negative, badly, when i put it back in drive, and go forward a few feet, my camber goes postive.......and my axle rotates. Balljoints are good, wheel bearings are good, and i just replaced the upper control arm...

Ok, i knew they were weak, but it ripped, both sides, it didnt come off, but close, threw a bead on it, but i need to make it alot stronger......whats my options........box the front only? Box, and guesset the sides....someone make a weldon mount thats stronger? set me straight please.

A few weaks ago my downstream 02 wiring harness got tangled up in my rear dshaft. It pulled one wire apart, and i but connected it back. Heres the problems my idle hunts, it will take a good 5-10 seconds of steady cranking to get it to start, after that it idles fine for a few minuets then...

I need some good write ups on how to build one. I have called a few places such as sam's offroad, and m.o.r.e and they told me there's would not be long enough. I am tired of wrap, i did a better rear end, and now i have to be eaiser on it because i continally break yoke adapters, its...

ok, i bent my last set of rk 4.5 springs badly, so when i did my 4:88's and rear detroit this weekend, i purchased the new 4.5 rk springs, brand new. Took out my 2 inch block, set the leafs on the m.o.r.e spring perch, which is supposed to be an anti wrap perch. A couple days later i see my...

Heres my problems, got a bad noise coming from underneath, we think its the tcase, or it could be the front end, hopefully the front since i am gearing very soon. The noise happens when i am in 4wd, either with a rear shaft or w/o, but never happens when i am in 2wd. Gets worse when i have...

Ok, purchased my clayton lift about a two months ago, it uses all rock krawler springs, and i know about the torque lean, but damn its bad. Whats my options on atleast getting it somewhat unnoticable? Getting ready to put a ford 8.8 in, and i can switch the springs from side to side if that...

I am getting ready to buy a set of 4340 27 spline chromo's out of a tj for my 99 xj, are both 30's the same or not, will they work?

Who makes a decently priced reclining seat that is designed for a larger person, and i mean width wise, not tall, i have broken most of the welds on my stocker?

Ok, i think i cut a bit to high lol. I cut past the body line where the flair bolts on, right about it, is this ok, and who makes a flair to go on this high? Also what do i do about the inner fender, is there any way to keep it? THanks guys

Hi, i am a new member here, and glad to be one, this site seems to offer a LOT of very good technical info for the xj owner. With that said, i just ordered my 8 inch long arm clayton lift for my 99 xj, and am gonna run 35 inch truxus tires. I would like to know what esle i will soon have to...