Search results

I'm having some death wobble issues with the jeep. I just replaced ball joints and checked the tie rods. I noticed a little play in the track bar joints. So I tore it all apart, and I cannot find the joints at all... They look similar to a teraflex track bar joint I seen but the joints I...

So I've been out of the loop on jeep's over the past few years but lately I've been reading up a lot on WJ steering. Right now I have a one ton setup OTK inverted T...pretty sure it has one Chevy TRE's. Everyone knows the con's with this setup...wondering, dead spot between 10 and 2. Track...

Basically I'm looking to get the cheapest code reader I can find that will tell me codes and clear them. I'm not using this for a business, so I don't need something from snap on or mac. http://www.amazon.com/U380-Engine-Scanner-Trouble-Reader/dp/B000LEPT5G

2000 XJ AW4 4x4 4.0 I had some codes on my jeep P1491 P0130 P0136 P0705 I also noticed no reverse lights, so I pulled the NSS off and cleaned out the yellow grease. I sanded down the contacts lightly and put it all back together with dielectric grease. Now the jeep starts in neutral and Park...

Ok, I've had a check engine light on for about a month now in my 2000 XJ with AW4 and 4.0. I was having a problem with Vapor Lock and I ordered the factory fix, which helped because it hasn't done that since the installation of the boots on all 6 injectors. Well, I've been driving it and the...

I have a 2000 XJ with a 4.0L and the AW4. My AC worked amazing last year, but the other day I went to turn it on for the first time and it wasn't blowing warm air at all. I turned the AC on and checked out the clutch for the compressor and I noticed its not spinning. I reas somewhere about...

Basically I need a fog light that will sit right above the mount itself. I don't want something cheap...I have cheapo wal-mart baja fog lights from another jeep that sit in front of the mount and they sit out from the bumper by like 4 inches. I want something thats going to be somewhat...

Ok, I have a 2000 XJ running a 4 bolt YJ box with plates on both sides of the frame rails and a custom 4x4 front winch bumper. I'm also running 1 ton OTK steering and a straight track bar that is flipped to the top side of the axle. My YJ box is less than a year old and is already clunking and...

Thats it, 2000 XJ not getting the horn sound all the time when using keyless...anyone know where to start troubleshooting? The horn works all the time so I don't think its a problem with the horn or relays. It works sometimes and other times it just locks the doors and doesn't honk. Thanks

I have an overhead console with wiring from a 2000 Cherokee. This can be wired to work in any 97+ Cherokee but will plug right into 2000-2001 Jeeps. I'm selling the temp sensor, the bracket, the wiring, the key fob(that works with the console) and the console itself. The console itself is...

Well I've seen a few write ups and no one seems to use RTV where the seals seat inside the axle housing but I figured I would ask to see what everyone else has done. Thanks in advance

I was going to change my inner seals today but none of the local part stores could get them. I found one place that I normally don't go to and they found a part number in a Timken book that was $40.00...I'm not going to pay that much. I found a link before where someone was selling them for...

Ok well my front axle seals are bad and I'm thinking about changing them tomorrow. I just have a few questions since I've never pulled the carrier in the front HP30. I have 4.88's and an aussie in the front, when I pull the carrier will the shims fall out? I know you have to pry the carrier...

This is for a dana 44 with 3.92 and up gears and stocker 30 spline shafts. I had this in my jeep for about 800 miles. -$120

New Brown Dog motor mounts - $60 Chrysler 8.25 29 Spline with factory Limited slip, around 70k - $250 Rubicon Express 4.5"? springs...the paint looks good but they are coated in a grease/oil mixture -$100 NP231 with partial h&t SYE -$200 Front Bumper from 84-96 Jeep Cherokee with fog...

Ok, I have a Aussie in the front and I hardly ever hear it make noise when in 2wd but I'm looking for a locker for my rear 44. What is the quietest rear locker? I'm thinking about doing an aussie like the front if I decide to lock the rear.

Well I have a spool in the rear of my jeep now because it was supposed to be trail only but plans have changed. The spool has been eating my tires lately since I have been driving it on the road so its coming out. I don't reall want to deal with the tires barking anymore...even if its...

As of now I would like to sell the jeep whole so if someone is looking to build a Cherokee this would be a great/cheap start. The blue tarp is over it because I was trying to keep the interior dry since it was basically in mint condition before the accident and I know some people may want that...

"The pitman arm converts the rotary motion of the steering gear to the linear motion of the centerlink. When a vehicle has a suspension lift installed, the pitman arm changes its position in relation to the centerlink. A dropped pitman is designed to compensate for a vehicle's suspension lift to...

Exactly as the title says, I have a complete 8.25 with 29 spline shafts. The rear end comes with everything including emergency brake cables. It's from a 2000 Cherokee with the towing package. The jeep had 70k on it. I would like to get $300.