Search results

So my 00 4.0 (cali emissions) aw4 DD has a suspected cracked flexplate. I want to get this swapped out in one day as it is my commuter. When looking at flex plates at both advance auto and rock auto, ATP shows 2 different plates for an auto. a .02 difference in diameter and one is "with...

Need a front driveshaft for my 00 auto. I completely forgot I took it out this summer because the carden joint had to be rebuilt and now need one before the snow Tuesday. I am working till 7pm tomorrow but can travel within reason to get one in the MA/CT/RI border. Help a brother out? I also...

Trying to install a used rk 3 link gen 2 we bought a few years ago and never even though the joints may not come out but sure enough all 3 flex joints the jam nuts come off but we can't get the joints to spin. We were planning on just putting all new joints in the arms. Last attempt I tried at...

Need an injector for my 00 xj (cali emissions if it makes a difference). Really just need one (mine is starting to have a crack developing in just one). Anyone got an extra kicking around? I'm in central MA but will pay for shipping.

I need one to swap into an xj for a couple months. Doesn't need knuckles, doesn't have to be HP, just needs to have good mounts and be able to drive in 2wd. Mount ripped off current axle and just need something to swap in while I fix the DD until we can do the axle swap and 3 link in a few...

My bud couldn't catch a break this winter, his 99 got hit by a plow in the rear 1/4 and insurance denied the plow driver was at fault so he bought Bob's 97 and 2 weeks later a kid runs a red light and smashes into the driver's doors. Insurance totaled it but he bought it back and we are parting...

Need this piece out of a manual: It's to keep the firewall from bending ever time you push the clutch. I also need a rear driveshaft about 32.5 inches long. Let me know what you got.

97 xj, 5 speed. Alternator appeared to be crapping out. 2 weeks prior my 00 was doing the exact same symptoms of gauge showing 14, then 12, then 9 after about 5 mins of running. On the 00 I didn't have time to test when I had finally grabbed my meter from work (was doing it after I picked up...

I need a renix era bracket that goes from the firewall at the master cylinder to the clutch pedals to keep you from pushing a big whole through your firewall when ever you press the clutch. I gotta get this dam thing going so I can wheel once before the snow flies. If you see one in a junkyard...

Ones I got from Billy must have been from a 2.5, too thin a diameter. My jeep is a 90 (renix) and I'm doing a 5 speed swap so I need flywheel bolts.

I'm broken down off 495/pike with a bad misfire (p0303) which usually only happens if the jeep is started with a hot engine after sitting. I don't have a good multimeter with me. I suspect one of my injector wires could have a short somewhere after looking through some tech topics. Anyone in the...

In about a month I'm hoping to start to finish my bud's xj so we can wheel by the end of the summer. There are 2 things outside of my ability and I was hoping to employee a UJ/Naxja member before going to a shop with it. We have an HP 30 and an MJ 44 which both need to be regeared to 4:56s and...

Got em? I need em. Even if they are used I can use em to figure out size to buy new ones.

Anyone ever run both? If so can you post pictures? We are going to be getting this combo for my buds 97. Our concern is the top control arm mount looks like it matches right with the stock uni-body. Anyone know if there is room to make it fit or are we stuck with chopping the stiffeners to...

Cheaper the better, I need something. I'm located in central mass. Let me know what you got.

Looks like my 2nd aw4 front seal is blown and I'm not gonna bother putting another one in while I have most of the parts for my 5 speed swap. Need a renix era Master Cylinder. Already have the pedal assembly in out of a 89 commanche. Also need an ax-15 crossmember. Let me know what ya got.

Going to the junkyard tom to get one unless someone on here has one and can save me the time to pull it. Need one for my 2000 with fuel rail and injectors on it. Let me know what you got.

So I have had an SYE for my buds jeep for almost a year now yet we haven't pulled the pin and done it. I have heard it's easy but I really would like to see it done by someone before trying myself, I'm worried I will miss something and screw up his tcase. Anyone willing to help guide me...

After a bit of searching I haven't come up with my answer. So here is my dilemma. I have a 2000 xj. I want to turn it into a nice clean looking dd on 245x70x16s. I bought a set of rims and sheepishly didn't check the bolt pattern. So I really do like these rims and I like alot of the 5x5...

Working 7 days a week and having 4 cars in line to work on I just can't fine the time to swap out my leaking freeze plug on my 00 xj DD. Anyone have some time and want to get paid to do it? I have the intake/exhaust gasket and a box of the plugs. It doesn't have to be a quick repair. I have...