jeep4play2000
NAXJA Forum User
- Location
- Kenosha, WI
I'm selling my custom rock crawler, because I want to be able to take the family with since we all enjoy camping and the outdoors... Hard to bring the wife, and 2 kids in this bad boy! SO! Onto the Jeep.
Drive line came out of a Jeep J20 3/4 ton. Dana 44 front with Warn hubs and Detroit locker 5.13 gear ratio. Rear Dana 60, welded, 5.13 gear ratio. Dana 300 T-case w/Twin Shifter conversion, 727 Trans vented for water crossings, AMC 360 engine completely built at Don's Auto in Kenosha, WI. Has mild Edelbrock Performer package. Frame is all hand-made from 1\4" Tube Steel. Had a frame company look at it at a car show and told me it was "One of the best frames they had ever seen" They wanted to know if the guy that built it needed a job, lol. The guy who built it is a Stainless Steel Fabricator by trade so there is a TON of S/S on here, and I mean a ton all done PERFECT. Short list of S/S includes, headlight covers, boxed brake light housings, complete rear section (inside and out doubled up), T-case shield 1/4" thick shield, Warn winch mount doubled 1/4", anti-wrap bar, steering wheel, steering column, complete exhaust, dash, etc... The list goes on and on...Has 35" Mickey Thompson Baja Claws, but has room for 44's if you want. Runs great, looks awesome, performs even better. Has TONS of power, will lift left front tire about a foot off of the ground under full accel. in 2wd low. Had vehicle professionaly appraised when I purchased it to take out a loan, it was appraised at "Not a penny less than 20,000.00" Certified Appraisal form will go with the Jeep. Pictures and talking about it really can't do it justice, you need to see it to believe it! It's located in Kenosha, WI. I'm asking 7500.00 obo. Will deliver for a fee, depending on where it's going. Winch not included.
Need to sell so I can build my XJ!! Help a brotha out! LOL! PM me for contact info!
Drive line came out of a Jeep J20 3/4 ton. Dana 44 front with Warn hubs and Detroit locker 5.13 gear ratio. Rear Dana 60, welded, 5.13 gear ratio. Dana 300 T-case w/Twin Shifter conversion, 727 Trans vented for water crossings, AMC 360 engine completely built at Don's Auto in Kenosha, WI. Has mild Edelbrock Performer package. Frame is all hand-made from 1\4" Tube Steel. Had a frame company look at it at a car show and told me it was "One of the best frames they had ever seen" They wanted to know if the guy that built it needed a job, lol. The guy who built it is a Stainless Steel Fabricator by trade so there is a TON of S/S on here, and I mean a ton all done PERFECT. Short list of S/S includes, headlight covers, boxed brake light housings, complete rear section (inside and out doubled up), T-case shield 1/4" thick shield, Warn winch mount doubled 1/4", anti-wrap bar, steering wheel, steering column, complete exhaust, dash, etc... The list goes on and on...Has 35" Mickey Thompson Baja Claws, but has room for 44's if you want. Runs great, looks awesome, performs even better. Has TONS of power, will lift left front tire about a foot off of the ground under full accel. in 2wd low. Had vehicle professionaly appraised when I purchased it to take out a loan, it was appraised at "Not a penny less than 20,000.00" Certified Appraisal form will go with the Jeep. Pictures and talking about it really can't do it justice, you need to see it to believe it! It's located in Kenosha, WI. I'm asking 7500.00 obo. Will deliver for a fee, depending on where it's going. Winch not included.
Need to sell so I can build my XJ!! Help a brotha out! LOL! PM me for contact info!
