• Welcome to the new NAXJA Forum! If your password does not work, please use "Forgot your password?" link on the log-in page. Please feel free to reach out to [email protected] if we can provide any assistance.

Search results

  1. A

    Some BIGDOGS pics

    I'm running 4.5 of BS.
  2. A

    Some BIGDOGS pics

    Yes its open to the public. Mostly though it is clubs, that go. bigdogsoffroad.com
  3. A

    Some BIGDOGS pics

    Bigdogs is in Gore, Va. No, those aren't tnt sliders.
  4. A

    Some BIGDOGS pics

    4.0/aw4/231 rubicon express 5.5" lift TNT Customs long arm kit F-250 overleafs 1.75" coilspring spacer 37x12.50x17 BFG Krawlers 17x9 TR alumium beadlocks 77 F-150 BB 9" shaved/plated stranger N case yukon 35 spline shafts yukon 5.13 yukon spool yukon alloys BG disc brakes...
  5. A

    Some BIGDOGS pics

    Some more.
  6. A

    Some BIGDOGS pics

    Just a few shoots from my first real trip of the year. Went down to Bigdogs.
  7. A

    Another xj on full widths.

    looks good. The only thing I see is to add more mounting points to the crossmember. There's going to be some stress on those four bolts.
  8. A

    97+ W/Cut fenders...washer bottle solution???

    I ran 35's with 6'' of lift without hitting the washer bottle. Only removed it cause I went with bigger tires.
  9. A

    97+ W/Cut fenders...washer bottle solution???

    I relocated mine. Pulled the whole assembly out. Then relocated it in the engine bay. I am running a aftermarket air filter. Zip tied the bottle to the MC, and the intake.
  10. A

    I've searched: rear TJ flair install

    http://www.cardomain.com/ride/588437/10
  11. A

    8.8 sources

    Your estimates are ready, just call the shop tomorrow.
  12. A

    ZJ Dana 44 shafts in an xj44?

    The ZJ D44HD have c-clips and I think a ABS mode ring.
  13. A

    8 lug hp d44 to 8lug or...

    http://www.naxja.org/forum/showthread.php?t=907066
  14. A

    ford hp44 with chevy flat tops

    Just grab all the outers. That way you can have a spare hub, shaft, and caliper for a core. knuckle, spindle, caliper bracket, caliper, hub, and stub shafts. You need a ford hub, rotor, and wheel bearings for the 5x5.5 Taken from Mr. N's page. Option 1: Use a mix of Chevy/FSJ and Ford parts...
  15. A

    detroit locker

    Just make sure that the locker has the right carrier break. 3.73 and down or 3.92 and up.
  16. A

    Moving to Sacmamento

    Thanks for the input so far. I should know this week if I am heading out west.
  17. A

    Moving to Sacmamento

    I was wondering if you guys could give me some input, since I have none. I am considering moving from MD to Scramento to attend Wyotech. Which is in west Sacramento. An eventually to SoCal, to addend TheFabSchool. I am doing some recearch now, but would like some input from people who reside in...
  18. A

    TNT Frame stiffeners?

    All you would need to do to add plug welds would be: Take the desired sized hole, get a hole saw. Then, drill out holes in the stiffeners and plug weld them. There would only be a hole in the frame rails where the pilot pit went through. That hole could be filled in when you weld it.
  19. A

    TNT Frame stiffeners?

    The install isin't that hard. Remove the crossmember. Then, soft pad the frame rails. Make sure to get the both sides and bottom. Next, clean and mock up the stiffeners. Using a bottle or floor jack to bend the stiffener to contour the frame rails. Also you can place the crossmember bolts to...
  20. A

    Full Width Steering

    For a beefy tie rod, drag link you can do this: d.o.m. or aluminium for the rod weld in tube inserts, bungs jam nuts 1 ton TRE's or heims (Make sure to have right/left hand threaded bungs, jam nuts, rod ends) For example, you would set your toe. If need be reem out the taper. Then, place the...
Back
Top