Search results

Want to build an axle for my 2000 xj and I'm leaving the motor stock. So, looking for a HP d30 to replace the LP. I'm in orange county.

I've searched ebay and the entire www to the best of my abilities. Anyone know of a source for the rear trim, top and bottom, interior at the rear hatch? 2000xj. Mine are cracked and we'll, I don't wanna try to repair.

Can someone help me ID a plug on my drivers side front door? There are 2 blue plugs that go into the door switch. Then there is a black plug that is clipped close to the top. I have no idea where this goes? Is it a speaker wire?

Ok, I feel like I'm fairly savvy at tracking down parts. However, every parts house in the world has every window regulator in the world, except the drivers side, rear power window regulator. Am I crazy? Anyone know where I can find one?

So, just thought I'd say hi. . Moved from Oxnard to mission viejo and figure it's time to take the old XJ out and start wheeling again. Seems like there's a pretty active 4wd driven scene down this way.

okay, I searched a ton, but no answers. I've got an ls1 that I want to swap into my 88 xj. I have pretty much everything figured out, well enough anyhow. But my question is how in the heck can I get it smogged in CA? I know it'll put out better emisions than the 4.0 in it now, but it won't...

After all the tuning I did, suddenly my 88 seems to just bne puttering out. I changed the TPS, plugs, wires, o2 sensor....and no for some reason, I'm getting crap gas mileage, have no power, and itt akes forever to start, occasionally stumbling. what's up with that?

I just realized that fo rhte past year, only two bolts were holding my trans to my blcok. are the upper two torx bolts dealer items? or can I replace them with something else?....

Well, for the past few weeks I have been chasing down a vibration in the 1100 to 1500 rpm range. I figured for a last ditch effort I would give it a tune up, and see what happened. On my 88 xj, I changed the o2 sensor, plugs, and IAC this morning. I started it up and let it idle for a bit...

This is sort of premature, but if I end up needing to put a new motor in my xj (88), what should I expect to spend ona short bolck, and where's a good place to get one...

Okay, so I've bene chasing this vibration in my tranny/motor for some time now. I have a thread in the tech forum. Anyhow, After changing the flexplate and harmonic balancer, I still can't figure it out. Basically, I get a vibration at 1100 to 1500 RPM. Before and after, it runs great. I...

It all started when I needed to change out my flexplate. I went to carquest and picked up a new flexplate. Which, by the way, was the only one within 100 miles of me. the dealer didn't even have one. weird. Anyhow, I changed the flexplate. I left the trans in the truck, I just backed it...

I forgot who put this link up, I think it was Dr. Dyno. http://www.jeep4.0performance.4mg.com/stroker.html But I am shopping for parts for a stroker right now. I HAVE to passs smog. I would liket use one of these combinations for my 88. Does anyone know if one of these specific combos...

Well I just finished putting in a new flexplate on my 88. 4.0 I didn't pull the transmission, I just unplugged a few connectors and pulled it away from the block as far as I could. Now that it is all back together, as soon as I start it, it sounds like the motor is breaking apart. It will...

Do I hve to "index" my flex plate. I am in the middle of replacing it with a new one because it is cracked, and since it has the ring for the cps sensor, I was wondering if I have line it up some how, or just bolt it on.

I picked up my 9 inch from Currie yesterday morning, and like a dummy I guess I figured it would have shock mounts on it. I'm figuring I'll just cut the old ones off and reuse them, plus that'll give me a little better clearance. does anyone see any issues with this? I'm also wondering if I...

Okay, in another thread I had asked about some steering questions. When I posted that I was going to run a 5" drop pitman, I got a questionable response. Is this wrong for an 8" lift? I am going to be running a RockKrawler lift and it comes with a track bar relocating bracket. the 5" is the...

My RockKrawler lift with Clayton hard arms is going on this week. I am waiting for a specific steeing set-up, so until it is ready, I have to run the stock set-up. I was wondering if ths is going to be a problem? I am swapping the D30 for a D44 and running 35" tires. Is there anything I...

Okay, I searched and got almost all the info I needed. I am swapping out both of my axles next weekend in my 88 xj. the front is a Currie D44 with the CJ Rotors and D30 calipers, and the rear is a 9" with Explorer brakes. I will be running 35's and 4:56 Gears. From what I gather on the...

This week I am swapping a Currie 9" into my 88 xj. I absolutely refuse to go sans e-brake. is there an easy way to hook the brake up? I am using the explorer discs from currie. I'm thinking it's a simple matter of hooking up the cable.....but what the hell do I know?