Search results

I took these off my GC for new rims and tires. Typical Jeep rim 5 on 4.5 by 16". Tires still have tread but are getting a bit worn down. 235/70/16 Looking to get $150 for everything one is a mismatch

I have a Ready Welder II 1000ADP that I just don't have a use for anymore. I haven't been able to go wheeling in over 3 years and as much as I would like to hold on to this I haven't touched in it in about the same amount of time. Even then I have only used it maybe 6 times at most. A few times...

I have a PSC cylinder assist kit. Their description says XJ and TJ but it could possibly fit ZJ I'm not sure. I had it on a 95 Xj with a full size 44 axle. The kit comes with steering gear(ported), high volume pump, reservoir/with bracket for XJ, hydraulic cylinder, and hoses. I would like...

Just what the title says and some more. Dana 60 axle ,Detroit Locker,5.13's,35 spline Yukon alloys,disk brakes with Cadillac calipers(parking brake style),BTF truss/diff cover ,and brackets for a 4 link. Asking 750..........................that is the price of the locker and alloys by...

i started a thread in Intermountain but i figured i share with everybody a little while ago i was given a 90 2 door Cherokee.since i want something to wheel and i sold the Tj tub, i figured i had a lot of left over parts from the last Cherokee.time to build another one.this one with a twist,i...

I'm selling a Jeep 4.0 stroker kit.this kit will make a 4.0 into a 4.5 - 4.7 liter depending on which rings you use and boring size. kit includes Pistons .40 over Rings Crank Connecting rods Bearings Cam The kit is over $900 in parts including the cam but letting go for $650.All parts are new...

i have a Comanche rear cab half i need to get rid of.it has a rear sliding window . looking to get $80 for it.

ok so as not to take away from the other thread this started on i will make a new one showing my point and that Olympic products are total trash. i can only assume that all this is for your winch mount bumper and not the whole line.under 2 years ago(6-05) i purchased a Rock bumper with hitch...

well the hydro-assist on my 44 is done so i thought i would share.its a fullsize uncut 44 with factory xj pitman arm.before this i had longer highsteer arms on it to clear the diff cover this caused it to lose some of the turning radius that the axle allowed.in the change over to hydro the...

this is a cross post from another board i'm on hey Ryan were famous,heheheheh

well i got a set of doors for 10 bucks. the drivers door had a good dent from the jeep being rolled.but for a set of half doors that are just going to get dented anyway. there are a few more here.i still have plenty to do but i will post more as i get more done.

ok i have a question for all those that have put a disk conversion on the back or have done a 44 up front. have any of you guys changed your master cylinder to something bigger?i just can't see the stock one moving enough fluid .i mean i would think that the bore and stroke of the stock one...

i have a front 44 axle out of an F250.it's a LP with flat top knuckles for highsteer ,driver side is already tapped.

well it would seem that if you blow an axle with a detroit locker it blows the locker as well just found this out today .also found that they will not warranty the locker if this has happened as well.so as of this point i will be looking for fullsize rears to toss under my rig.dana 44 front 60...

what it says a factory rear hitch for a cherokee.looking to get 30 bucks for it . in Layton ,Utah

so me and Dr.Moab went out for a drive today.went to Bountiful Canyon came across this nice sight. so we had to give him a hand right,hehehehe i drifted off into a snow bank and got stuck for a bit .he winched me out and we were back on are way.he has some pics he might post .

i have been looking for this for a bit and finially found it again. deep diving a fj40

i don't know if you are up on this or not but i'm on several boards that are using this bulletin system .most have choose to shut down becuase of the issue till a patch has been produced .it might be something you want to investigate on your own system -----BEGIN PGP SIGNED MESSAGE-----...