Search results

Got a new to me 2000. 5V signal to the engine sensors varies form 5.5V to .003V. Still runs most of the time, but I should get a replacement before it quits completely. Any body have one laying around?

Who do I contact to reset the password on my Naxja email account?

Mine has been having overheating problems for a couple of years. It finally gave up a couple of weeks ago. Took it apart, found 2 cylinder walls cracked. Some one I know from work offered me a block from an engine swap he did, so I ordered rings and bearings and gaskets and such, got the new...

Any idea where to find one? I tried all my usual sources, and no luck. Thanks!

It took a while, and there aren't very many, but here is a link to my pics. Sgtmack's picture album

My 99 4.0 lost an injector driver. The local salvage yards seemed confused as to what a PCM was, so I checked with the local dealership. Ouch. Are there any aftermarket sources for PCM's? Or did this stupid Jeep just cost me another $550.00? And yes, I'm going to replace the injector for that...

It looks like I will be in Alpena the first two weeks of June. Are there any places to take the Jeep while I'm there? Or should I just plan on fishing for two weeks. Neal

http://www.naxja.org/forum/showthread.php?p=243758340#post243758340 A bump for this thread in the Land Use forum. If any one close can make it, it might help us keep a wheeling spot open. Neal

First, I have a 99 with an 8.25 rear with 4.56 gears and a front Aussie. It will be on 33's with a 4.5 inch long arm lift. I like rocks more than mud. So, if I can't do both, which should be next; 1. Alloy axles for the front. I'm on my third set of axles in two years, but the last set were cv...

I'm going from 3" to 4.5". I'm going to build a long arm front suspension. I think I have figured out how to fit a URF style 3 link. The question is should I use bushings at the lower axle ends for a better ride, or JJ's on all the on all four lower joints so it feels more solid. I'm using rod...

If any one is interested, the Rocky-Road Supersliders I won at WF are for sale. I've decided I need a locker more than a new set of rails. http://www.naxja.org/forum/showthread.php?t=909824

I have a brand new set of sliders I won at Winterfest. these things are Beefy. But I already have sliders, so I want to sell these and buy a locker. You can check them out at www.rocky-road.com/rockrail.html They are still wrapped for shipping. I would prefer local pick up, but I can arrange...

I found another cheap hack n tap option for those who are looking for an easy upgrade. www.driveshaftsuperstore.com sent me a new yoke for $99.00 plus shipping. Here is a pic installed. Install was pretty easy, it even came with instructions. Pros- Used a front shaft with no extra adapter...

I need a new tie rod , mine looks like a pretzel. I have an abundance of 1 1/4 1/8th wall DOM. Is it strong enough on it's own, or should I use it to sleeve a piece of 1" solid. I'm leaning toward using both, but I haven't figured out the whole assembly concept for solid, tube, and welded...

Some one had to start this one, so I guess it's my turn. I'm assuming you all know the :NAXJA: required equipment, and you are all smart enough to bring extra socks, but what about spares, tools, beer:wave: ,etc? I might be able to score a generator to run my little flux core MIG, and a bring...

A few pics I got when I wasn't breaking stuff. http://www.midwestxj.org/Gallery/album08

Here's my question: I have a little money put aside,and I'm not sure what to spend it on. I don't have enough for a locker, darn it, but I can either buy steel to make rocker rails, or a make a CO2 tank setup. Which should I do? :wave:

Woo Hoo! I made it to 100 posts! Look at me go! :sunshine:

Quick question. I used to have a link to a source for weld in inserts for 2" square tube, but my hard drive died. Any body heard of them? I have access to tube and a good welder at my new job. I see a long arm setup in my future. If I can save up enough money. :banghead: