Search results

1 dana 30/35 Detroit ez locker needs pins and springs $75 1 8.8 lsd 3.73 axle stripped $150 needs brakes Dana 30 3.73 gears Buy the thirty 8.8 and locker for $350 and I'll throw in two spare axle shafts! 5 35X12.5 general grabbers currently mounted on 6X5.5 rims but I have 5X5.5 rims and 2...

Looking for a dana 30 locker. And a 3.73 8.8

Re lowers $60 goodish bushings flex joints are tight. Rustys uppers $100 $140 for the pair to red letters Tnt belly pan good shape $125 Trooper axle out of a 97 61" wide with a meh driveshaft $200 $150 for red letters 4.56s and disks Alloy rims 6X5.5 r15 5 for $250 225 for reds outlaw...

I bought a 1997 jeep grand Cherokee with a 5.2. Anything I should know about? It has the factory trans cooler and the motor and trans where rebuilt 3-4k ago. I know the vic sucks. I know it has a lp 30 and 44a with a rear ls my current plans are to swap my np231 use Clayton rear brackets and the...

I'm parting out my Rig. Dana 44 out of an early bronco converted to 6 lug Detroit locker solid diff cover and alloy USA chromos. Disk brakes and ruffstuff steering. Setup for an xj or tj. Isuzu twelve bolt welded setup for a xj would probably work for a soa mj $1500 for the pair will not...

I set my trooper axle up for a four inch lift and a inch stretch. Cycled the suspension and it won't clear the gas tank so I am going back to my original plan of rocking it in the stock location with 2 inches of lift. Seeing as I burned on the perches for a 4 ish inch lift and am going back to...

TNT belly pan $120 Rough country track bar $50 Xj control arms rustys uppers Rubicon express lowers $150 for the four or $100 for the uppers and 75 for the lowers. Dirtbound bumper $150 has a few dents.

I'm looking for 37s I have 800.

I have an awful miss fire. Everything seems alright as far as the sensors go they all are right where they are supposed to be throttle body have been cleaned yada yada. I am thinking that because my coil was cracked that replacing it would have helped. It did but only to an extent. Could the...

Thinking about parting my xj out or selling hole. Fully stiffened. Through the floor shocks. Dana 44 front 4.56s detroit chromos and warn premiums Ruffstuff steering. Rear 8.25 29 spline Welded 4.56s Rubicon express lowers Rustys offroad uppers IRO track bar all bushing sleeves bored out...

Any one have one for sale my jeeps a 98. Also willing to grab a zj skid.

My powertrax gernaded so I want to weld the rear, any one got any 29 spline spiders that are near ct or willing to ship?:us:

So from what I have gathered its a 9.5 ring and pinion, no clue on the u joint... Can be found with a factory air locker and its 31 spline with a common 4.6 ratio that would work with my 4.56 front. How strong is it and the factory rear locker? Also the 12b it is stupid common had 4.56s and...

I have a dana 60 and 10.5 out of an 04 f350 and I know it is a sixty. I dont know if I want to build it because I have an xj with 2.5 inches of lift and 35s decent short arms and a dana 44 front, 8.25, and I have 4.56s The only issue I have with the axle is I am eating hubs when I get stupid...

Cheap but decent is preferred 4 or more.

Would a slightly hopped up 5.0L Out of a mountaineer or exploder be that bad of a swap? It has the GT40P heads, and a good intake. It runs pretty cool for a V8 as well. It is a small engine, and if what I am reading about TJ swaps is true it seams like you can get every thing to play "nice" With...

My jeep sat for 5 months while I did my axle swap. During that time I changed my Trans lines because they were leaking bad! So it drove fine in December I parked it and started my swap then as soon as I got it done (today) I put it in drive and it was kind of low so I put fluid in it and in...

I'm looking for some cheap 37x12.5r16.5 tires for my friends beater rig. Decent shape and reasonable price would be sweet.

I have a 88 header panel and wiring harness $50 Axle shafts 1 complete set and a Spare short side $60 Rustys control arms bushings in both ends $50 4.0L out of a renix 88 with 135k on it ran like a top just needs a timing chain Comes as a long block $150 Complete with manifolds $200...

I'm looking for a 4.56 geared rear axle, is prefer a 8.25 29 spline or a 8.8 open or lsd is preferred. Let me know what you have.