Search results

Hi all, I just wrapped up installing a Dana 44 rear axle that I purchased from East Coast Gear Supply (they make new casting, bolt in axle assemblies). I just went on a few test runs this morning and now have a vibration / shudder that starts at 20mph and picks up with speed. It lessens a bit...

Does anyone have experience with 2.5" Skyjacker Softride leaf springs? I'm looking for a good quality 2" leaf spring and recently found these. Unfortunately, there are no reviews online and I can't find anything on the forums. Aside from these, seems as though there are a few ~1" options and...

Hi all, I just put the engine back together after replacing my 0331 head with a replacement from Promaxx (formerly Alabama Cylinder). I started it and let it run for about 10 seconds before deciding that something wasn't right. It shook and sounded really uneven. Maybe a cylinder (or two) isn't...

Hi all, What's the trick to removing the electrical harness clips on the fuel injectors? I can't seem to figure it out - also don't want to pull too hard and break them.

All, I'm installing a SYE this weekend and want to remove my TC drop. Is it safe to put a jack under the transmission pan to support the trans and TC while I remove the crossmember and take the drop blocks off? Seems trivial, but don't want to dent or damage the transmission pan.

Hi all, Replacing the exhaust manifold on my 2000 and looking to use new hardware. Seems as though there's a mix of nuts, bolts and studs. Does anyone know if there's a complete kit out there? There isn't one from the dealer... Dorman's kit goes up to 1999. Will that work on my 2000?

Hi all, Replaced the drag link and tie rod today (as well as all tie rod ends). I did the whole job with the wheels on the ground. Do I need an alignment? Don't see how anything could have changed.

Hi all, I'm in the process of doing a front end "restoration", replacing old worn parts with new. I want to tackle the track bar next. I'm currently sitting at somewhere between 1.5 and 2" of lift. I'd like to get a new, adjustable track bar as well as a new frame mount. My existing frame...

Hi all, In the process of installing a new trans cooler and plumbing. I'm going to be using -6AN fittings and Russell Twist-lok hose throughout. Is there an adapter out there that I can use to replace those annoying quick connect fittings at the radiator?

Hi all, What's the size of the bleeder bolt on an 8.25? I tried my smallest wrenches (5/16" and 8mm) and they were both too big.

Hi all, Installing a trans temp gauge and need a 12V Ignition Source to run it. For a 2000, is there a good ignition-controlled 12V source that you recommend in the vicinity of the center console? Also, very basic question... how would I use a multimeter to check for 12V? Drive a pin into the...

Hi all, I'm lucky enough to have the California emissions package on my 2000 with the precats. I recently got a ScanGauge and have been keeping an eye on my IAT readings. When driving on the highway, temps are 20 or so degrees above ambient. When I'm stopped or in traffic, IAT temps rise...

Hi all, I have a manual electric fan override switch on my 2000. It's is fully operational (thanks to an awesome write-up on this site: http://naxja.org/forum/showthread.php?t=1025399). I'm using a simple SPST switch to run it - flick the switch and it provides a ground signal to the relay...

Does anyone know were I can get replacement u-nuts / speed nuts that mount the top of the mech. fan and electric fan to the radiator support bracket? I called the dealer and they said that the pattern is 10mm x 1.5.

My electric fan, which I have wired to a switch, seems to be running much more quietly as of recently. Before I order a replacement fan, I want to make sure that the fan is getting the right amount of "juice" to verify that there isn't an underlying electrical issue. How would I go about testing...

I’m going to be replacing my 13 year stock radiator with either a Griffin or Flex-a-lite unit. Both companies make direct fit OEM replacement options. I’m not worried about the money. I want high quality that will last (plus good warranties on both). I’ll be keeping the stock fan set-up...

I’m in the middle of installing C4x4 tow hooks and I’ve run into a problem. I cannot get the bumper back on with the tow hook supports installed because of their extra width on the outside of the frame. I’ve noticed in a few write-ups that guys have removed the bumper brackets from the bumper...

I have a howl in 4WD. As a first diagnostic step I figured that I would check the differential fluid level. While the level was OK, the fluid was green. The consistency seemed fine, but the color was a pretty vivid green color - almost like antifreeze. What could have caused that?

I’m considering buying a 63mm throttle body from Leigh Performance to complement my new Borla exhaust. First off, is this a worthwhile upgrade? Second, I reviewed the installation procedures for the Jeepers and Creepers TB and at one point they have you trim a section of the throttle shaft...

Last fall I used 4WD for the first time in a few months and immediately noticed a high pitched noise that only occurred when decelerating (i.e., foot was off the gas). Imagine a jet spooling down, that’s the best way I can describe it. I replaced the TC with a new Jasper unit. There was...