Search results

Camshaft sensor can cause a no spark condition at the coil?? If so I will give it a try! I'm willing to try anything at this point. I pulled every grounding point in the manual, cleaned, scraped, and re-tightened with no effect. I also tried the battery disconnect and re-connect to reset the...

The coil on my XJ is mounted directly to the block. Where is the ICU?? There is 12v at the coil with the ignition on.

Re: '93 XJ Dead-No Spark at Coil..Still Please Help! Well so far I have replaced the coil with a known good one, the computer with a known good one, and the crank sensor with a new one. I checked all the grounds, removed and re-installed them. I verified that I had power from the ignition to...

Turned off the XJ for just a few hours and then it wouldn't start. I checked many of the other threads and it sounded like the CPS. I bought a new one (80.00 Autozone..ouch!) and still no spark. I replaced the coil with one from my other XJ that runs and still no spark.. Should I try swapping...

Oil can Henry tested freon levels and they showed fine. I am told the switch is a common failure. Jumping out the switch will kick in the compressor and cold air in side. Any other ideas?

Sorry, it is on a '97 XJ. Thanks again!!

Just wanted to find out from someone that has done it, if the low pressure a/c switch does in fact have a shrader valve. I would perfer not to release all of my Freon. Thanks for the help!!

I bought a '92 XJ for my daughter (I have a '97 with a Rubicon 3.5 Superflex) and she would like the keyless entry remote if possible. It is a Laredo and it has the overhead console with the little black half round ball towards the back of the console. Does this mean that I can buy an IR remote...

Harbor Freight has a reader w/ reset for about 40.00... I like this system myself. I can't stand the stupid 1-2 position on this tranny. It always drops into 1st when I want it to stay in 2nd. This looks like the fix for that!

Does the Powertrax require re-aligning the gear mesh and etc. like when changing gears?

What are the teflon pads supposed to do??

Did you put in a xfer drop? Did it sit higher in the back when you first put it in? I have had mine in for about a week and it sits too high in back and also has a vibration when accelerating.(In reference to Semper Fi...)

Thanks for the info!! I can't wait till it levels out. It really looks silly! Thanks again! Bob

I have a '97 XJ with an open rear axle and I am getting very tired of spinning one tire when the roads are wet.(which is most of the time here in Oregon..) What would be the best upgrade for a daily driver. BTW, I have installed the RE 3.5 Superflex w/ leaf packs, xfer case drop, and RE...

I just put in my RE superflex 3.5 with full leaf pack on my '97 XJ. I was advised to install the xfer case drop kit to avoid vibration. I installed everything and I now get vibration ONLY when accelerating. According to the RE instructions this means I need to install shims. My question is what...

Thanks Rocketman! I know what you mean. I narrowly missed the power steering line on the drivers side. I will double check. Bob

Thanks! I also have not checked the alignment of the axle yet...Duh! I will check the axle alignment and hook up my adjustable track bar THEN check the QD alignment. Thanks for the heads up on the adjustment! I did not even think about being able to reach the storage pin for running with them...

I am in the process of installing my RE Super Flex and got to the QD's and the upper and lower sections don't appear to be lining up very well. The instructions are not very detailed. Does the lower pin that mounts to the axle bracket go on the inside or the outside of the bracket? Any help...

Another naive question. Is the website for Rusty's "rustys.com" or what. Also, what exactly do I need? Thanks for all the info! Bob

Will I really need an longer yoke with a 3.5" lift? I am doing the 1" TC drop as reccomended by Jeepin outfitters where I bought the kit.