Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Welcome to the new NAXJA Forum!
If your password does not work, please use "Forgot your password?" link on the log-in page.
Please feel free to reach out to [email protected] if we can provide any assistance.
Does anyone know the bolts sizes for the bracket to sway bar and the disconnect to bracket? Also is there a good alternative to the button heads?
1999 XJ 4" lift
I just installed a banks monster cat-back and the tailpipe is hitting the rear shackle bolt. Dose anyone have any suggestions on either shifting the tailpipe or somehow protecting it? I was thinking maybe wrapping that section in exhaust wrap.
I have recently noticed that when I break hard or breke at highway speeds the Jeep violently pulls to the left. Thinking it might have been the calipers I replaced them on Sunday with no change. I put new tires on it on Tuesday as well as an alignment so I think I can rule those out as well. I...
My 1999 xj has developed the following problem.
While accelerating there is a bucking/hesitation that feels similar to hitting a bump in the road.l would appreciate any help diagnosing this issue.
4.0 with 186k
My airbag light was on and my horn stopped working so I replaced the clock spring, but the problem persists. Does this mean that I need a new airbag module?
Thanks
Last week I changed my old motor mounts and now on occasion when I accelerate there is a hesitation for a few seconds until it catches. Sometimes accompanied by a clunk that can be felt. Is this a tranny problem or could things be out of alignment because of the new mounts?
Hi all
Does anyone know the size of the bolts that attach the locking mechanism to the rear hatch? As well as where I could find one? 1999 Cherokee Thanks!
So I got in to an accident and snapped the lower control arm mount on the axle. Does anyone have a recommendation on a good aftermarket replacement?
Good news is that the Ironman 4x4 CA's are still straight as an arrow.
Am am going to do this as soon as the bottle arrives. Is there anything I should know? or is it as simple as taking the old one off and putting the new one on? Thanks
I have been getting this clunk from the right rear when making left turns or going over bumps. I have gone under the jeep checked for loose parts and everything is tight with no play. I took the right rear wheel off today to see if there might be something going on with the brakes and have found...
Hi all - I am running 31" tires on wheels with 3.75" back spacing and a 19mm offset. I need to buy a spare and wanted to ask if it mattered what the back spacing and offset of the wheel are?
I got an alignment today and the camber on the drivers side is -1.1* my FSM has the preferred camber as -.25* with a range of -.75* to .5*. I know that I need an upper ball joint on that side so my question is will a bad ball joint cause the camber be so far out of wack? Thanks!
1999 Cherokee...
Problem 1 I have a dead spot in my steering when turning I the right. It takes a good third of a turn in the wheel until the tires start to move. I had my cousin move the wheel and everything is tight seems to work properly . The tie rod ends do seem to rotate very freely ,but no side to side...
mods please delete duplicate post
Problem 1 I have a dead spot in my steering when turning I the right. It takes a good third of a turn in the wheel until the tires start to move. I had my cousin move the wheel and everything is tight seems to work properly . The tie rod ends do seem to...
I recently purchased a 309 Craftsman piece set and a Homak 3-Drawer box. All of the sockets are loose and I am looking for ideas on getting them organized. I looked at rails, but it will get a bit pricy for 178 sockets. thanks in advance.
Does anyone have this set, and if so what do you think? Thanks
http://www.amazon.com/Craftsman-Mechanics-3-Drawer-Flip-Top-Chest/dp/B003VCMX0Y/ref=sr_1_1?s=automotive&ie=UTF8&qid=1354723211&sr=1-1&keywords=craftsman+mechanics+tool+set
I have been having a problem with my head lights where they would randomly blink off. At first I thought it was because the switch was not properly anchored so I used some velcro and anchored it but the problem persisted. I then noticed that the wires directly behind the plug were really hot...