Search results

I plan on doing a regear soon to 4.88 In the spring. New bearings/seals will come then. Perhaps maybe a new full case ARB or OX locker. Might as well save the hasel of doing it twice.

hey i got a chrysler 8.25 and have had similar symptoms, especialy not locking in reverse. Which i know that when i got it, it always locked in reverse. I have replaced the springs once with some improvement, but has continued to stop working. I havnt checked any clearance specs but i do know...

I reguards to the 5-speed extended Idle I still want to know myself. 98 XJ ps. already have hacked the gray pin 12 and is out in the open ready for the next step.

i too have a 98 cherokee 5-speed original harness, but i have upgraded the harness with a pin and wire comming from the pin 12. I ground it but nothing happens. what else is needed to make it work on a 5-speed?

I got a 98 XJ Se model, with 107k miles, Zero rust, 4 almost new tires, wrecked front header panel front bumper and rear hatch (glass shattered, and felt it just was easier to replace whole hatch. Starts, runs, and drove for 100 bucks,( one hundred dollars). Found right paint code for all 3...

While in neutral and on a flat surface with ebrake on my rear drive shaft has a serious amount of play. The twisting motion back and fourth feels like an inch or more of movement. When going in reverse and then putting in the clutch(still rolling back, just no engaugement), it almost gets this...

hey will you do 50 bucks shipped to 01462? If so I could get that paypal out to you ASAP. This is for both items. Thanks Tyler

Hey yeah what is the best way to try and center the axel to be able to get it adjusted? I got the adj. track bar but it doesnt seem like i could get it centerd very well. Im a perfectionist. hah I also herd about caster adjustments on the control arms? How do these work? How to adjust? and why...

So after installing all of my RE components on my 98 XJ and installed my 33 BFG all terrains i have a rubbing issue on flat ground. Now i did expect to have to trim some to fit BUT the problem im having is that with the tires turned to one side the tire will clear just enough to make the turn...

What exactly is going on with their leaf springs? I have just received my 4.5 kit this past week and plan on install this weekend. But I don't want to run shit leaves...

To follow up. I got the trans and engine seperated. I now have access to my clutch and components. Turns out the return spring ( very light duty) that connects the throwout bearing with the clutch fork was broken. Resulting in clutch release and engagement problems. ANY PARTS TO REPLACE other...

thanks yeah sounds like LUk over in the wrangler section is the way to go. Anyways got into tearing out the tranny for inspection and got all disconnected and unbolted, but the tranny and engine will not split. We have gotten the (aluminum like sleeves to come apart at the edges were it meets...

Well to follow up on MY clutch problem. my master and slave are both in working order. I pulled off the slave from the bell housing to see whats up. Well come to find out that the piston on the slave is all hung up behind the fork. The fork feels and looks as if it has come unhinged from the...

As I had asked before is there a good aftermarket tranny mount for the 5-speed. Also would I notice vibes since, its not in gear at idle?

I got the SAME exact problem. Clutch pedal went to the floor, and then ended up binding up like something is caught. Its a 98, 5-speed, ax-15, 101k mi, 3.07 gears, dana 30 (front) Chrysler 8.25 (rear). Please let me know what the best quality replacement parts are and what they are. Thanks

It only sounds at idle. At around 2k rpm i get a tap. Top end?

Recently I have been getting that diesel and sound of marbles being rolled around together under the hood. I have just over 101,300K mi on this thing it is just recently started doing it. I have changed the oil in it at 99,779 with synthetic Valvoline 10-30. I change my oil more than often, and...

Does MOORE sell a good tranny mount for the ax-15? Also are the Ax-15 and auto mounts the same bolt in wise? If not MOORE who sells a good tranny mount that will last. Also since I will not be experiencing vibes at idle because of the 5-speed should i skip on the torsion rubber and go all the...

Wait Is there a difference between 4.10 and 4.11? I am getting confused as many on this thread had mentioned both as if the same thing? I am right or wrong?

Agreed it looks awsome. What brand and height listed and actual is that lift? That front trim looks nice, as well as the rear. I like the rubicon wheels too.