Search results

Could anyone direct me in the right direction where to find a single cylinder ring set? Everywhere I've looked they want to sell me a 6 pack. I found some on rockauto, the first two listed (http://www.rockauto.com/catalog/x,carcode,1363384,parttype,5640) but they say they are specifically for...

I am parting out a 98 XJ Sport, purple-ish with 73k on it. Everything ran/worked fine when pulled. Here is a partial list of what I have Both passenger doors & rear drivers door Good shape. Some small parking lot damage (a ding or scratch) $100 each w/glass & no electronics. $150 w/window...

From my deaceased 87/4.0/auto/2wd (power brakes) I had it about 2 weeks before the MJ died. Like new but has been in the garage for about 6-7 years. Located in Michigan. I could ship it if you want to pay shipping.

Any tricks on getting rid of mold on seats & carpeting? I picked up an impound XJ and the interior looks like my fridge back in college. I was thinking of using a mild bleach solution w/pressure washer to clean the carpet (if the bleach discolors it I will dye the carpet, no big deal) but I am...

Has anyone actually swapped out their "2/3" roof rack on a 99+ to the longer "full" rack from a 97-98? I have seen the subject discussed & searched but didn't find anyone who had actually done it. My main concern is the drilling for the threaded inserts. How and what did you do? TIA for any...

I figured I would post a mini write up since I had to r/r just about everything under the hood. Here is how I installed an inline aux. trans cooler & temp gauge on my 00XJ. This line is the input (from trans to rad) line. It is a hard line which I had to cut (see arrow). I used a tubing...

I need to replace the warped flexplate in my XJ and was wondering what years are compatible.. I have a 2K, AW4/231. I know the Renix ones will not work as their timing is different but would one work from any H.O. or do I need to go 97+ or and I stuck with finding an exact year replacement. TIA...

I have check my FSM and searched without luck. After replacing the rod bearings my XJ won't start (2K). The only electrical item I touched was the cam position sensor and I have quadruple checked it (has 5v, and I reset it to FSM specs) I have checked and there is no spark and the injectors are...

Here is the fuse & related circuit information that DC neglected to give us 97+ XJ owners. All information is based of a 2KXJ and the related manuals. Everything listed is a circuit that is either "attached" to the fuse or directly impacted by it. If anything is incorrect please let me know...

Has anyone done (or know someone who has) a rear disc conversion on an Eagle,Concord,Evil Spirt etc. with the rear AMC20 (5x4.5 bolt pattern) and ZJ hardware? I scored a complete brand new setup from a local freecycle group and I have already done the XJ and can't decide whether to do the...

Just wanted to see my name in red! :wave:

Flame me if you must but I am having a brain fart.(no luck in searh) Do I need to use 4.0 main bearings or 4.2 mains for the stroker? (I can't remember what I put in it and can't find the receipt to check) TIA Nathan

Is there a tranny (2wd or 4wd) that would be a direct bolt up to a 2.8 that could handle 300hp? I am dumb when it comes to GM parts knowledge & interchange. TIA Nathan

2K 4.0 Auto. Are you supposed to reset the computer after you replace the idle air control motor/valve? If yes, could it cause issues if you don't? Thanks for the input. Nathan

Anybody ever use these? http://cgi.ebay.com/ebaymotors/Poly-Motor-Mounts-for-Jeep-Cherokee-TJ-YJ-XJ_W0QQcmdZViewItemQQcategoryZ50454QQitemZ8014907223QQrdZ1QQsspagenameZWDVW I am a little scared off the quality/durability of them and the fact they are ebay only. Any input is appreciated. Thanks...

00 XJ 4.5/AW4 I just switched to dual electric fans and want to remove the fan pulley/bearing assembly. Diagram of both oem routing and my proposed routing. www.paceenterprises.us/belt My concern is that there may not be enough belt contact. I don't wheel in water or mud & the engine...

Thinking about a new winter project and I stumbled across a nice deal on a 2wd 1990 MJ w/a blown 4 pooper. What I wanted to know are what chassis modifications are needed to bolt in 4.0 block? All I can think of would be the motor mounts & a tranny crossmember (putting in a 904). Anything...

I have a brand new set (16) of Comp Cams 926-16 valve springs. They will work with a Comp Cams 68-231-4 cam. $78 shipped. I also have a brand new Cloyes cam timing gear for a 2000 4.0. $35 shipped Please let me know asap on the springs if you are interested. If I dont sell them by Friday I...

I have a brand new Cloyes Cam Timing gear for a 00 XJ 4.0. The part# is S822T $36 shipped in the continental U.S. Any questions please let me know. Thanks, Nathan

Sorry about the title spacing, I don't want anything to pull up on google. (Bad experience before) Due to my recent house purchase, I need to sell my motorcycle. It is a 97 B M W F 650. It is black/gray and in excellent condition. It has 42xx miles on the 650cc 48~hp, 50~ftlb single cylinder and...