Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Welcome to the new NAXJA Forum!
If your password does not work, please use "Forgot your password?" link on the log-in page.
Please feel free to reach out to [email protected] if we can provide any assistance.
here is the deal, my 91 xj is draining the battery if i let it sit for more than a couple days without starting it. i've narrowed it down to something on the "dome" fuse under the dash. its drawing .21amps and i cheched the current draw on my buddies 91 xj and he gets exactly .21amps draw when...
i want to do a sye on my 91 xj with a 242. i bought some parts used but i'm not sure if i have everything i need to use a front driveshaft off another xj in the rear. the guy sent me the yoke to go on the output of the t-case and an adapter for the yoke so a stock front driveshaft will bolt up...
my powers seats on my 91 limited started acting up intermittently a couple weeks ago. sometimes they would work, sometimes they wouldn't. now they don't work at all. i checked for voltage on the switch and its fine. there is even power going to the motors when i push the buttons. so i would have...
My 91 xj, 4.0 AW4 will not start. about a month ago i couldn't start it or even get any power with the key turned. I found that alot of my battery wires and grounds were really corroded so i replaced all of them with new 2 guage wire. that fixed the problem. now after driving it for over a month...
I know there are tonnes of threads on this subject but they don't answer all of my questions. i have a 91 xj and want to know exactly what new parts i need for this swap. I have the whole doner 99 so i can take whatever i need from it. so far from the other threads i have read that i need...
I have been having some problems with my xj since i bought it about a year ago. today i was doing some investigating and found that while the engine is running, if i spray wd40 on one area of the intake manifold right near the back of the engine where the gasket is, the jeep boggs down slightly...
I'm not sure if the Idle Air Control is working? When I disconnect the IAC harness while the engine is running it doesn't change anything it just keeps idling the same. and when I pulled the IAC out and looked at it the pintle does not move in and out freely when i try to push it in and out. is...
I just did a code check and it had the following codes:
12- Battery Disconnect
51- Fuel System Lean
55
so what could be the cause of a lean fuel system? I figured if anything i was running rich with the 8-10mpg on the highway i'm getting. :dunno:
I had this brilliant idea the other day to mount my hella 500 6" round driving lamps in my grille. I was going to cut holes in my grille large enough to fit the lights and then fab up some rings that will finish off the cuts to make the holes look like their meant to be there. then i will mount...
my 91 4.0 is acting strange lately. i installed a vac gauge a while back so i could check for problems and still have it mounted in the cab. when i start up the jeep it idles around 800rpm and is at about 17 on the vac gauge. but after driving for a while when i stop and put it in park it revs...
i made the upgraded headlight harness and it works good. only problem is that i have factory daytime running lights here in Canada and the lower voltage that my daytime running lights put out is not enough to keep my relay on the new harness switched on. it just kinda hums and vibrates. so i...
can anyone say if any of these parts are a good deal? thanks
http://winnipegheights.com/forums/showthread.php?t=194030&highlight=jeep
(keep in mind these prices are in Canadian dollars)
my 91 cherokee has a oil pressure guage. but its a Canadian xj and it doesn't read in psi, it doesn't have any units of measurement on it so i'm not sure what its reading or what it is suppossed to be reading? any know?
i have been getting alot of oil in my k&n cone filter and i decided to build a oil catch can. i made one out of aluminum with a sight glass in it and i gues the heat from the engine melted the silicone i used on the sight glass so it fell out. i just checked and noticed this. so for possibly two...
i seen a couple posts about using a higher amp alternator out of a grand cherokee. just curiouse which years of grand cherokee will fit? does it require any modificationsto fit? what are the benefits of doing this?
thanks:wave1:
so when i was trimming my rear fenders for the bushwacker install i cut the seam to the point that there is a 1/4 inch gap and even up to a 1/2 inch gap in a couple places. what is the big deal, what problems can i run into? i don't ever do any rock climbing, only wheeling in snow, sand and mud.
I want a new engine for my xj, the one in it is in good running condition but is getting old and tire and i need more power. i want something that will be an easy, drop in install. i was thinking of a couple options.
1- buy a stroker.... drop it in.
2- have the engine rebuilt as a stroker(but i...
i want to wire my new hella 500's so that i can turn them on any time the vehicle is on regardless of wether or not i have high or low beams on. i also wqant to use the factory fog light switch. does anyone have any ideas of how this can be wired easily? i was thinking of doing the same setup as...