Search results

1992 jeep wrangler rock crawler this is not a daily driver, it is street legal and i drive it around town but its not a highway/daily driver. 4.0 liter 6cyl motor 5 speed transmission np231/dana 300 doubler transfer case with triple stick cable shifters grill hoop 8000 lb winch with wireless...

np231 from a 92 yj. input shaft swapped to 21 spline. works fine just upgraded to a doubler. $250 located in fort collins

looking for a 231 cv (double cardan) yoke. fort collins area would be a plus but would consider others as well.

4 33 12.50 15 bfg km2's in good shape. minor rash. all 4 have 10-11mm of tread the spare is a 33 10.50 15 bfg ko. it is good enough to limp home on but not in the best of shape. tires are not on wheels. but i do have a set of 5 15x8 5on 4.5" wheels i can make a package deal on. $750 obo for the...

anybody need a hp44 and 9"? these are from a 76 f150 but the front axle has drums and is missing the short side shaft. but does have the welded on wedges. was told that they have 3.50 gears. $250 for the pair. located in fort collins

i recently installed some new uca bushings on my dana 30. and after about 100 or less miles the rubber is squeezing out of the sleeve far enough for the other end of the sleeve to be rubbing on the arm itself. has anybody else had this happen before? or did i just get a crappy set of bushings? i...

i'm looking for 1 or maybe 2 36" tsl's with around 60% tread or more. will most likely need it shipped to 39564. let me know what you have. thanks

i'm looking for 1 36-12.50-15 tsl with at least 60% tread. let me know what you have. thanks

i'm trying to figure out where this wire goes. it goes to a sensor on the drivers side of the block. it is wrapped up along with 2 other wires. those 2 wires go into the plug for the sensor and this one is just hanging out all alone. anybody know where it might go? this is on a 87 mj 4.0

i'm looking to get rid of the comanche. spec are as follows 1987 jeep comanche longbed 4.0 aw4 np231 6.5" lift up front 4.5" lift springs and 2" spacers rubicon express superflex uper control arms rubicon express superride lower control arms rough country control arm drop brackets rusty's HD...

i'm looking to get rid of the comanche. spec are as follows 1987 jeep comanche longbed 4.0 aw4 np231 6.5" lift up front 4.5" lift springs and 2" spacers rubicon express superflex uper control arms rubicon express superride lower control arms rough country control arm drop brackets rusty's HD...

i know rusty's sucks but my jeep already has the rusty's HD trackbar and bracket. does anybody here run rusty's trackbar brace? it looks pretty weak just by looking at the picture of it.

selling my posi-lock $100 plus shipping. located in south ms

looking for a lunchbox locker for a dana 30. let me know what u have.

i need a set of drop brackets. i only need the brackets. the braces won't work on a mj so i don't need them. let me know what you have.

anybody ever done this? i did recently when i mounted a fuel cell. let me know if you have and if there were any issues. some guys on another site had some concerns with it that it was unsafe due to it being designed to be in the tank. here are some pics.

are the perches in the right place to swap an xj rear axle into a mj soa? or will the perches need to be moved?

thinking about selling my rig and getting something more of a dd/mild wheeler. here it is. 1992 jeep cherokee laredo. the body has 200,000 miles. motor was replaced 60,000 ago with a jasper engine. automatic transmission was also rebuilt at that time cold a/c 5.5" rubicon express lift with...

anybody know where i can get some upper bumpstops? i'm running a re5.5" lift but the rubber upper bumpstops are gone so tire to inner fender is the current bumpstop. i'm thinking the stock height ones will be enough. anybody know where i can get some? rubber or eurathane

anybody know how tight the adjuster side of the flex joint should be torqued to when rebuilding a RE large superflex joint? i hope to be installing new races in mine tomorrow if the parts get here. thanks