Search results

Anyone regret going 1 tons? I was going to make the move a couple years ago but ended up selling the axles before I swapped them in. Now I kind of the bug to hop on the 1 tons and 40's bandwagon all over again. I have your typical XJ on 35's with highly polished 30/8.8 combo. For trail...

2000XJ AW4, I am wrapping up my doubler-D300 swap. I accidentally bought a short shaft D300 instead of the long shaft so I can't swap my 231 spedo into the D300. My rig is more or less trail only, any issues with just leaving the speedo harness off and giving up on the guage or will I suffer...

I installed a strongbox-231 doubler in my XJ and am looking at fabing new crossmembers. What is the school of though on mounts. Do people have luck sticking with the just the stock tranny mount? add a 2nd off the doubler, or just run one of the doubler and ditch the tranny mount? I am...

Let see some pics of how you guys mounted your PSC external resevoirs. I have the new style CBR pump with the latest gen reservoir. I can't see any way of keeping the res output above the pump without it sticking a inch or two through the hood. I would like to see some options before I punch...

I am tracking down some 231 internals to put in my new billet rangebox that is going in front of a dana300. I have the option of 231c from a 96 chevy. I understand this will be 4 or 6 pinion planetary. My question is the input shaft length. I have a 2000XJ with the aw4. I understand this...

anyone know what size bushing I need (upper) for a KOR/JKS trackbar?

There are large oragne orings that seal the pressed in axle tube to the center hosing on a dana 30. Anyone got a partnumber for these? Here is a pic from Stu Olsen's jeep site. Again, not the actual inner axle seal, the large orange seal is what I am after.

I am regearing my axle very soon. My buddy has a dana 44 ubolt style yoke and claims it will fit my dana 30. Is this true? Are the yokes interchangeable?

I am preparing for my E-Locker install in a hp30. I have purchased the requried special bearings. It just occurred to me that I did not think about shims. If the bearings aren't stock then I am assuming I need special shims as well. The instructions do not mention this at all, only the need...

I need to drive a good ways to pickup a new set of 35" MTR's I ordered. I need to cross the border and pay tolls so I don't want to bring my trailer if I don't need it. Can I fit a set of 4 inside my XJ?

I am running ruffstuff perches on my 8.8 They are 7.75 inches long which help with axle wrap. I need some matching 7.75" or longer degree shims as I am going to add more lift to rear. Anyone know where I can get some?

I am installing a 30 spline locker/shafts into a hp 30. Just realized that the inner seals that came with my master install kit probably won't work. Do I need special seals? I was thinking maybe a TJ rubicon 44 seal might work. Anyone have part numbers? I only have the locker so far, do...

I am going to pick up some 2"x1/4 tubing to sleeve the inside of my dana 30 axles tubes. I want to get it turned on a lathe to true up the external diameter and bring it down a bit so it slides in easy enough. I know this had been done before but I couldn't find any info searching, how many...

Want to go to 5x 5.5 on my disk brake explorer 8.8 out back. Is there an off the shelf rotor that will work?

Need some real world info here. Waggy 44 lp 44 swap. Is anyone running one at 5.5-6.6 " of lift? If so I am looking for some info, What is your pinion angle, How is it setup in relation to your driveshaft, or better yet can you post your pinion angle and your front driveshaft angle...

Need some info quick, does it matter what year YJ steering box you use for the 4-bolt box swap? I was told there might be a difference in that not all use 0-rings on the fluid lines. I stripped the threads out of mine and if I can find one quick I will put one in as I already have the 4 bolt...

Anyone know what the angle difference is between the spring perches and the pinion on a stock XJ axle?

Anyone got the torque specs for the 8.8 brake hardware. specifically... Caliper bracket/mounting plate bolts Spicer pinion flanger adapter bolts

I am ordering everything for my 8.8 swap right now. I am running 31x10.5 tires on my stock wheels. Will I need to order spacers or can I get away without them? Being in Canada I want to order everything at once to save on shipping. I can't find a clear answer to this.

I welded up the orginal hole and drilled a new one when when I first did my lift. The origninal hole was wallowed out so I added some plate to the front side of the mount to increase the bolt engagement. Now my new hole is wallowed out and with a Kevin't TBC in the mail I need to look at...