Search results

Hey guys, I am getting the family out of CA and moving to the Knoxville area near the end of Dec. Honestly considering selling my jeep to a member out here in CA because I am not sure how much I would use it out there. It also seems like most people just have sxs out there. Is there more to...

I have a pair of 5.5" leaf springs, Iron Rock Offroad, that I am replacing. They are worn in but would be good on a budget or to build a bastard pack. I also have a set of Ruffstuff leaf spring retaining plates. nothing wrong with them just replacing with the kind that have the extension...

I am looking into adding an aux fuse and relay box to properly run some electrical. I am looking at the following but was not sure if I need the relay side bus too, dual bus, or just the fuse side. I assume just the fuse side sense what I understand I should go from batter to bus to fuse to...

I will be selling my d44 30 spline Detroit and Ford 9" 31 spline Detroit in a couple months. Just throwing this out there in case someone is looking. The front d44 locker currently has a broken side gear. $100 part to fix. $50 as is or $200 and I'll fix. Rear is fine just swapping both out for...

I once found a dude in I believe the north west that sold a rear stiffener for the inner rail and wrapped to the bottom as well. I can't find the site now. Anyone have a link or know if he is still making them?

https://photos.app.goo.gl/s3IJoZkzSftlCkYf1

I bought these quite a while back and never needed them, running standard stuff. I have two right and one left. These are "Chevy 1 ton" offset ends from Ruffstuff. Shoot me a reasonable offer.

2001 xj Jeep would turn on with the key but would not turn over, not even a click from the starter. Few days later it fired up and then on the second start the starter cut out after a second. I checked all the fuses and swapped relays no luck. I turned the key on and jumper the starter...

FYI Incase you guys want to meet up with some So Cal guys. http://www.naxja.org/forum/showthread.php?t=1136157

I have had a misfire on cylinder 5 and swapped out the coil. That seemed to help a lot but is getting worse again and just threw another code, I still need to scan the new code.... Just wanted to start a thread and get ideas rolling. I need this fixed soon to pass smog...

I realize most are heading to SierraFest and I wish I was too. Anyone up for Barrett this weekend?

I will be in the garage again tonight. Goals. Hydro assist and new sway bar links Rear stiffeners too but highly unlikely tonight Located in EDH Post up I you want to head over

So am running a 44 front with Ruffstuff hi steer arms and a true cross over steering. I have a TNT truss and room is tight between the axle side pan hard bracket and the tie rod. I would rather not cut up the bracket but want some more turning radius back. I bought some offset TREs but space...

Let me know what you have

I have a PSC hydro assist kit now so i need to figure out how to mount the ram. At first glance my two possibe options with my setup are below the tie rod, not great for the rock but could build a skid, or behind the tie rod and under the pan hard. I read about measuring throw and sway, I feel I...

Mechanics cover donated by Rick- Chris (NorCalChris) CB radio - Karl (BigKintheXJ) Head light restoration kit donated by Rick - Eric (EricsXJ) MREs donated by Doc Moe - Jon (Blondejoncherokee ) RWK Haus Yukon Yoke - Josh (XJensen ) gifted to Lou Mechanics cover & head light restoration kit -...

Got home and just got back from the pool with the kids! Thanks to everyone for making this a great trip. It was great to see old friends and make new ones. Post them up!

I need to get a little more depth on my Ruffstuff high steer arm. The high angle drag link end does not seat in deep enough to get the but on

Frame side drop brackets. Price 1 22oz American brew

LL Bean waterhogs I can bring them to SierraFest if needed or you pick them up here.