Search results

Hey i'm trying to take apart a 231J and i can't seem to get the case to split... am i missing something? I took out the tail housing bolts and knocked that loose, i took out the bolts holding the retaining something or other on the input side and removed the two snap rings... inner and outer...

What would i need to swap from a 242 to a 231. I have been looking because my 242 is getting ready to blow and i don't have any 242's around here to replace it. So what i'm looking for is what is different between the two that i can try to plan for. I hear that the front driveshaft yokes can...

Just got my hands on some 15X10 wheels and i wanted to know if you guys thought they were too big to run 33's on? I heard handling would be affected greatly... if they are too big should i go with 15X8's?

Hey dooes anyone have caps for the master cylinder resevoir the junkyard around here wants $10 each for them and the dealer discontinued them. thanks ahead of time.

i think the title says it all. Just let me know what you got... the closer the better.

Hey did anyone hear about these closing? I read it some where else and was wondering if anyone else heard it.

Not seeing pictures.. most come up with the red x... not mine, others. Any ideas?

I just put my new cb and 102" whip on my truck and for some reason it only picks uo and transmits about a 100 yards. Any ideas? I know it's grounded but what's this about a ground plane? I'm gonna research but there's alot of guys that have their antennas mounted on the bumper and i would...

So my heap has a noise and i cant figure out what it is so i thought hey a video would have the noise on it. I have a flowmaster so don't listen to that... there is a noise that sounds like an exhaust clamp rattling but i replaced the entire exhaust system... listen for it... any ideas?:dunce...

I saw someone talking about first gear lockout in an automatic which would make sense cause the shifter bezel say 1-2, 3, Overdrive N R P but in my truck if i put it all the way down to that 1-2, gear then it never shifts out of first until i move it up...or if i downshift it will go straight...

I know there have been a lot of threads about oil pressure and the sending unit but i have one for ya. My oil pressure is very low (0) but only when i am sitting still or pushing on the gas. When i am coasting the pressure goes up (25). Push on the gas it goes back to 0. Changed the sending...

what would you guys say about going from completely stock dana 35 w/ABs to Non C-Clip d35 with Lockrite and 4.11's for 150 dollars at my door. Is losing the ABS worth it or even possible for just the rear? or should i just buy the axle and put the stuff in mine (more expensive...gear install)?

my low tone horn went out so i bought a new one, unplugged the broke and one and pluegged the new one in and it didn't work. so, i plugged the new one into the working horn and it wasn't working there either. Now, no horns work anywhere. Is this a fuse problem? if so where is the fuse, or is...

I've got a prospect jeep... it's a 91 xj 4 1/2 in rough country lift, interior is shot, couple dents in the truck, 30/35 combo new track bar new pitman arm possible 31's(unsure) dunlop radial rovers, small oil leak, stock bumpers and stock interior. What would you guys say this is worth? All...

i have some parts from when i put my lift on ... 4 shocks w/brackets and bushings front springs, lower control arms and sway bar connects all stock from a 94. 5 dollars plus shipping for what ever you want otherwise it's trash...

i have done some searching and haven't found anything that sounds like what i have. I own a 94 4.o auto with a 242 4.5 lift... First when I am driving and i take off from the light i hear a rattling noise at the end of first gear right before it shifts to second. I had thought for some time...

i have a 50 series delta flowmaster brand new 2.25 i/o center/offset make me an offr if you want it. Shipping on your money.

I have a 94 and my entire passenger side floor pan is starting to rust and get soft. I think a defective cat sped up the rust problem. I replaced half of a completely worn out part where the carpet was the only thing between me and the ground and now i'm gonna start to redo the rest but i...

I bought some new fog lights for Christmas and started wiring them with the heavy duty wiring kit. I ran the line from the lights to the battery to the relay to the switch, and then from the switch i'm lost. Where would i plug into the fuse box under the steering wheel or how would i wire in...