Search results

Long time since I've poked around, but still seem some old Winterfest names. Got a new project for my son and I. 89 short bed Comanche, 2000 xj donor. We've completed the swap and are finishing procedures for initial startup. Effectively it is a 2000, no wiring splices for inside the cab or...

HP d30, 4.56 gears, TNT truss so mounts aren't stock. Custom front shaft, RE adjustable uppers and lowers, drop brackets, 5" lift measured dirty way. Ok so I've been fighting a drivability issue as I'm wanting to take jeep off trailer and drive to more trails-it drives like my caster is too...

First off 2000 with coil rail distributor-less ignition system. 4.56 gears and 265 tires (32") 232k miles roughly 90k on engine block. Jeep runs like an unmotivated turtle. Below 2k rpms has decent power anything above that it is gutless. Partial throttle gives same response as full...

D30, 4.56, Cryo Treated so im trying to get them setup tight like i was told to from Bobby Long. Pinion shims are around .42 (my drink spilled on my notes so thats from memory) Pinion Pre-load around 18in pounds Backlash .004 Carrier pre-load is good, no side to side movement and tight Drive...

Out of my 2000, a 242 with RE H&T and a rebuilt front shaft with the correct flange on it, it all bolts up. Tcase has some miles on it, but chain seemed to be in good shape. Had slight vibes around 80 with it, but my pinion was just a tad high. 250 OBO for the package, includes the wiring...

d30 297 joint shafts out of a 2000 lp d30, you can have the whole axle, you can have the axles and hubs, you can have just the trac bar, tie rod, drag link, whatever you want. The price on any item is 100 bucks. 3.55 gears if you want to take the whole thing.

jeep is up for rig of the month in the picture showcase... http://www.naxja.org/forum/showthread.php?t=1037218

I'm wanting to pick up a cordless impact for the trail. I've seen one of the makita's in action and was really impressed with its weight/size for the power it offered. Anyone have any experience with any brand or specific models i should look into?

I'll start with the few my wife shot when she wasnt worried that i was dead...

Driving home from a run with the jeep on the trailer and have a question. Was on a muddy trail and the front end was spinning then made a loud pop. Tires will still spin but front end pops, clunks and makes all kinds of noise. Tires occasionally lock up but if you give it some gas it will pop...

anyone heading out to ROM have an extra electric fan laying around? Mine has decided last minute to quit operating...

have a 2000 with a recently replaced master cylinder due to soft brakes. Did a gravity bleed on the brakes, still soft so took it to a shop and they ran it through 2 vacuum bleeds and still got a soft pedal. Ive got two opinions thus far and looking for some clarity. First opinion is i have...

just had my axles regeared to 4.56's 8.25 rear with an auburn ls. Have been driving the setup for about a month now, two trail runs on it. Sunday was out wheeling and all the sudden back in started grinding-thought the limited slip wasnt disengaging and got it home. Finally opened up the rear...

these come with hooks, brackets and brand new hardware from c4x4 55 shipped for red members, 55 plus shipping for forum users

help with a 97 jeep searched and found threads about fuel pressure being too high and fuel pressure being too low but couldnt find anything about being all over the place at idle pressure bounces all over the place from 30psi to 55psi, with a small bit a throttle it will settle in to 45-47...

http://www.naxja.org/forum/showthread.php?t=1009560

Hitch $40 D30 ring/pinion 3.55 $20 8.25 ring/pinion 3.55 $20 8.25 ring/pinion 4.56 $55 (less than 100 miles) Stock Front Skid Plate $20 Stock Diff Covers D30/8.25 $20 bucks for both shipped Stock Bumper end caps for front, trimmed on bottom $10 c4x4 tow hook brackets with tow hooks $55 (no...

just as it says-do i need to be looking for a deep cycle or what? 5500lb winch what size of battery do you guys suggest-trailer has no charging system just want a battery on it in case i need it i can charge it myself for as much as the trailer is used.

Can someone run a ford vin number for me to see what engine is in a car. My dad is looking for an engine block to begin building for his 65 falcon. Found this car as an old police car, and was hoping it had the 351 police interceptor. Vin 2facp72g9mx118556 any help would be appreciated-even...

I've searched, found a million threads but havent seen one that really helps me out. Put a SYE on my 242 (HnT only option) had a machine shop tap it for me. Got a front driveshaft, had a shop do a complete rebuild with spicer u-joints, balanced and everything. Shimmed it so the pinion angle...