Search results

OME 934's and JC1A's w/RE shackles and OME long travel shocks (3" lift) Adj lower control arms and JKS sway bar disconnects, 31x9.50 TSL radials on Canyon Rims. BPI rear bumper, KargoMaster rack, AJ's front bumper w/ push bar, Reflexxion Cowl hood, XJ Nation skids. 4:10 gearing, Posi-lock...

Most all of the OME lift stuff is on now and she looks a bit jacked up in the rear.... I get center of axle to lip of flare measurement of ~20.75 front and just a smidgen over 20.5 in the rear with maybe a little under 100lbs of junk in the back. From what I find this sounds just right and that...

Would anyone be able to send a pic of their A/C setup on their V6 XJ? I pulled a compressor and the brackets from an 85 or so S10 blazer thinking they'd be the same to put in mine since the PO for some reason removed it. I didn't have time to mount it all up myself when I got it and now when we...

Finally slapped on my bumpers. Other than having to torch a little off the back end of the reciever tube and sawzalling the fenders the AJ's front went right on. The BPI rear was cake other than having to use the come along to wretch the old DS nutstrip out since the hitch had been removed with...

I am surfing / shopping for a new gooseneck trailer and need to figure out what length I need to get to fit the XJ and CJ both on at the same time. The XJ is up at one of my garages right now with the bumpers off so I can't go measure it right now..... I need to know total length bumper to...

Later this week I am going to start doing the lift install and was wonderin if anyone had some links to some decent write ups? Since My lift is sort of a mix match of parts I really didn't get any instructions, most of it I think is pretty straight forward but I know the XJ has it's own little...

After I got the hood install done today I decided to go ahead and tackle replacing the fender. I had no idea it would be such a PIA. All but 2 of the flare studs broke off and the last 3 torx screws behind the nose panel look to be next to impossible to remove without removing the nose panel...

Is it possible to switch the 84-86 style hood latch out for an 87 up style set up? Or is the radiator support completely different and it won't accept it? I'm thinking I can use threaded inserts and bolts to mount the striker on my new hood but thought I'd explore the other possibilities. Mike B.

Just ordered a new 04 F350 XLT last week and bit the bullet and chose the 6.0 PS instead of the V10 like I originally planned. I was assured that the upgrades that were made a few months ago fixed all the issues that the 1st ones off the line had, and the warranty is pretty damn good. Anyways...

Title pretty much says it all, and yes I do have it sized correctly & all that. It took one for my profile just fine but I've never been able to get it to take my avatar. Mike B.

86 XJ V6, installing OME 934's, JC1's, & terraflex shackles. Will I need adj LCA's? Adj trackbar & hd mount is already on order from Kevin's. Already searched and nothing really came up that helped, & since OME is real vauge about net lift #'s all I can do is guess I'll end up at around...

Let's try this again.... Gonna be installing OME 934 front coils, JC1 rear leafs, & terraflex shackles. My guestimate is approx. 3"-3.5" net lift.... is this about right? I'll be installing an AJ's front non winch bumper, BPI rear bumper, and I already have a Cargo master roof rack with the...

Just ordered up all my OME lift from StageWest.... Here's what's coming - OME 934 GC front springs, JC1 rears, M35 & 36 OME shocks, spring bushings, longer SS brake likes, Terra flex Greasable shackles. I also am waiting for the HD trackbar conversion from Kevin's. I'm taking a WAG that I'll...

242 question Going to look at a XJ tommorow with my BIL (89 I think) and I know it has the 242, whats the best way to make sure the tcase in it is OK what are the early signs of a 242 starting to go bad? It sounds like a decent deal on it, but not if the tcase isn't ok. I only ask cause I've...

Just a note for the archives, when doing the 2.8 - 3.4 swap make sure the 2.8 flywheel or flex plate is machined and 0 balanced. The 3.4 is internally balanced so the 2.8 flywheel which is externally balanced will cause the 3.4 to run a bit lumpy from idle to about 2,000 rpm. The PO of mine had...

Need a FSM for my 86 XJ. Mike B.

Was hoping to get a FSM from the dealer but that was a no go. Techauthority only lists back to 94 on the website.... didn't call the 800 # yet though but I'm guessing nothing will be available pre Chrysler from them. Mike B.

Occasionally when comming to a stop I'll push the clutch in and I'll have a metal to metal sound, sorta like the sound a completely shot set of brakes make when they are down metal to metal. Could it be something in the AX5 like something sticking? Maybe too heavy of a gear oil was used in it by...

What are the symptoms of a worn out tcase chain? My 207 has 265,000 miles on it and I have no idea if it has ever had a new chain or bearings put in it. Hopefully not related.... Occasionally when comming to a stop I'll push the clutch in and I'll have a metal to metal sound, sorta like the...

Need an explanation of how the air pump system works... or should work that is. Just installed weber, ran manifold vacumn to air pump system control valve. Seems I'm getting exaust to the air pump and it's blowing the fitting out of the back of the air pump from time to time. I'm assuming that...