Search results

can i get the connector off of the newer starter and mount it on the older one so i can use the facory wire connector instead of cutting it off and putting a round eye on it?

my son broke down last nite in his 2000 cherokee. it died and wouldnt start as he was driving. we pushed it into a lot and found that a vacuum line had popped off on the intake just below the throttle body. i found it on the ground right where it originally died and it started once put on again...

this is on my sons 91 xj with a front 60 and a 14 bolt rear.front and back are 3/4 ton chevy disc brakes.we installed this over 8 years ago and have not had a problem with it ever.this rig is mainly driven on the street.when we installed these axles we swapped to the corvette equal reservoir mc...

I need to install an adjustable prop valve in the rear to keep it from locking up on hard stops.i have a 14 bolt with discs in the rear.ive done this before on other vehicles but ive always installed them in the rear by the diff.the problem ive encountered is that they got cruded up with mud and...

after much searching on here ive come to the conclusion that the leafspring bushings are the same as a stock 94 wrangler.1.5 inch in the rear and 2 inch in the front. can I just buy a cheaper poly set for the 94 wrangler to use on my 91 xj?

the one in the transfer case.mine is a 91 and has only a 2 wire connector.can i swap it for a newer 3 wire sender?the newer style is plentiful in the junkyards and mine seems to be a special order.i recently replaced my gage cluster and all of the connectors went together without any...

the 2000 has no dist.will this engine accept a dist?could i swap the 94 dist in this engine?should i keep looking for something older?

im looking for 2 or more 38-39 inch swampers in central nj.can be 16.5 or 15 in rim.

91 xj 4.0. ive just replaced just about everything with my no start issue.now it starts but idles and runs like it has a bad miss.the plugs are brand new.i pulled them after running for a while and all look brand new except the rear #6 one which is black.i pulled the plug put the wire on and...

this is a 91 cherokee with the ho 4.0 engine.during the last very cold blast here it would not start after i went to the store.after a bit i got it going and home(just a mile or 2)the next day it still wouldnt start.i suspect the fuel pump.i disconnected the fuel line forward of the large filter...

it reads discharge for a bit then after driving goes up to where it should be(14 vlts)in the morning it cranks slow and the chk eng lite comes on sometimes.the batt is very old so i replaced it over the weekend because it failed all of the tests at autozone.everything seemed fine that day with a...

i have 2 of each side windows and 1 rear window.all used only 3 times.black fabric and clear plastic windows.these are jeep brand not aftermarket.looking to get 150.00 for all located in central nj

the nut holding the yoke on came loose and the yoke was woobling.i took it apart ,cleaned it up and locktited it back on but i think the seal is shot noe because its leaking a bit.do i have to get a new seal from porc?can it be cross referenced to one at a local parts store?also i...

its the stock one.i replaced the motormounts recently and they were completely gone.i can push up on my tranfercase about 3/8 of an inch or so.should there be that much play?is there a stronger one out there?

sometimes my 94 xj has no power but seems to rev up fine.this doesnt happen all of the time though.i checked my exhaust system and the front of my muffler is broken and the pipe is loose inside of it(the muffler appears to be pretty new)im suspecting the cat or maybe the broken pipe is getting...

to get more angle out of it.ive done it to toyota cvs before.there are writeups on it.the 1310 is different then the yota stuff though.its acyually assembled backwards from how the yota one is.

i have to pull the whole assembly from one in the junkyard.will any yr around 94 work?ive been looking at replacement procedures and it seems the plug changed at some point.

ive read some writeups and they all seem to remove everything including the linkage.can i juat replace the motor by itself or will everything have to be removed?

he claims its a universal fit and originally bought for his 2003 jeep.i cant find any info on it on the k=n site. http://images.craigslist.org/3n33m23oaZZZZZZZZZ92af3773d2f85ee1dc5.jpg thanks

sorry no pic.they are brand new, he claims they are rear 6 in for a jeep xj.they have been sitting for a few yrs in his basement and they have no eye bushings.both ends are military wrapped and there are 5 leaves.they clearly have this stenciled on the top leaf 4WD240. anyone know who may be...