Search results

installing a OBA setup with a york 210. Looking for a international or kenworth part number for the serp cluth. lowbuck setup.

Does anyone know if there is a yoke to use with AA sye kit that would use a normal u-joint, not the cv style shaft. trying to use a non cv driveshaft.

Looking for a hp ford that can be cut down. Must have leafs or weld on perches.

I just picked up a 78 bronco axle complete and noticed it has cast wedges on it. will I be able to use this to cut down to waggy width?

does anyone have pics of these mounts? searched and the one link would not work. anyone?

Hello all, I'm in need of a full width nine inch ( bronco, pickup, van) rear housing. The one I have is bent on one side. Could use whole axle or just the housing. looking for something on the cheap.

Has anyone else used the 136 amp durango unit? I'm wondering if I will need to upgrade the charging wire to a bigger gauge? I have a suzuki that I changed the alt in it and smoked the charging wire while winchin. Any thoughts would be helpful.

Hello, I'm trying to install a taurus fan. I would like to have the fan come on automatically, with a factory style fan switch that threads into the coolant passage. I'm trying to find a switch that turns on at about 190-200 any help would be appreciated.

Went to take off my box tonight and two out of three bolts snaped off in the box! Should I replace these with jeep bolts or should I use grade 8 equivelents? Also if anyone has any rebuild kit part#s to napa that would also be of help. Since I have to remove the box to get the bolts out I may...

I have a 93 with 3 inch springs and 3 in. blocks in rear. I'am running this set up with 31s now. I put a set of 35s on to see how much would need to be cut. It looks very possible to do! I'm looking for any pics or experiance with this setup, before I begin cutting.

Does anyone run these and if so do you have any pics of how they look. Thinking of making a pair that lift motor 1 inch. The motor mount bolt seams to fit loose in the LCA bushing. Any ideas?

I just picked up a R&P from a non disco front. Will I have any problems installing this in my non disco front axle? Both are dana 30HP. I have 3.55 now and this will match my 8.8 rear. Thanks.

Hi all, I just installed a 8.8 in my 93HO with aw4 231 and the ford yoke I bought is too wide for the factory ujoint. the part number I used was E9TZ-4782-B. Does anyone have any idea what could be the problem wrong part#? Thanks.

Has anyone used a setup just like the front longarm but in the rear? I made one for my samuari but never got a chance to wheel it. It flexed great! I'm just not sure how it would work in the real world of wheelin.

I'm going to build some front long arms any idea where to buy the 1 1/4 threaded rod and some inserts for 2 in. square tubing? I'm looking to make them adjustable obviosly. I'm going to use a bushing holder at one end and a johnny joint at the other end.

I'm looking to sell a 01 ford explorer 8.8 with 4.10 factory gears. It also has brand new rotors, comes complete with calipers and brake lines, and e-bake cables. Also included are a set of 1.5 inch wheel spacers (from trail ready) and the ford driveshaft adapter to go to a 1310 series...

Any one know where else to get some of these? I'm looking to use them for motor mounts, and control arms. http://www.rocklogic4x4.com/store/index.php?action=item&id=102&prevaction=category&previd=bestsellers&prevstart=0

I'am about to swap a waggy 44 in front, and wondering what is the best way to make the upper mounts. Also how thick is the plate that people are bending to go over the diff housing? Would 1/4" be enoungh or should it be 5/16"?

I have a 01' exploer 8.8 disc braked complete with calipers and sway bars, new in the box rotors and the yoke adapter to go to a 1310 u-joint.This is a 4.10 ratio with 70K miles on it. Bought it from a yard in conn. Looking to install a toy rear end. I would like 450$ or B.O.

I just put a 93 ho on the road. My previous rig was a 90 that I just put the yellow top injectors in. Are the HO injectors the same 4 hole design? Should I swap them in place on the Ho injectors?