• Welcome to the new NAXJA Forum! If your password does not work, please use "Forgot your password?" link on the log-in page. Please feel free to reach out to [email protected] if we can provide any assistance.

Recent content by Clean Racing

  1. C

    H.O valve cover causing idle problem on my renix

    How about what valve cover did you use? Is it the stamped steel, or an alum stock one, or one of the aftermarket ones from crown, omix. It may not have the rear baffle sealed properly. SO there is a possibility....
  2. C

    Stand Alone ecu questions.

    So this may be a lot to ask. Does anyone have a VE table for the 4.0L and possibly a timing table for the 4.0L used for stand alone ecu's. I am looking at ditching the 20 something Renix and possibly going with the AEM infinty 6 to run the jeep. Normally aspirated, no boost planned for this one.
  3. C

    H.O valve cover causing idle problem on my renix

    How do you have the two ports plumbed. I ran the back one with a smaller nipple to the intake manifold like a pcv system. And the front is plumbed into the intake tube like a breather.
  4. C

    WTB.. steering shaft for a 90 XJ.

    Hey Ben. Im not sure if a 94 is the same. Jeep list them from 86-93 for some reason. I managed to cut up the three I have and make one that works for now. Thanks for offering up Ben, Take care.
  5. C

    Wanted 1990 XJ steering shaft.

    Mods can delete this thread. I cut up three that I had and made one that works perfectly now. Thanks.
  6. C

    WTB.. steering shaft for a 90 XJ.

    Hey Socal peeps. Since my exile to the NW, I no longer have the luxury of a junk yard run. SO I am in need of a steering shaft that goes between the column and the box for my 90 XJ. Thanks.. Scott.
  7. C

    Wanted 1990 XJ steering shaft.

    As title states, I am in need of a steering shaft for my 90 that goes between the column and the box. I am in Bellingham and two cars down right now. I am also looking for a vavle cover for the 4.0 as well. Thanks. Scott.
  8. C

    Jeep Cherokee & Grand Cherokee header/exhaust by Mopar Performance

    Will you ship?
  9. C

    Ford Nine inch set up for xj

    Interested, also in Bellingham. sending pm so you can text pics. Thanks.
  10. C

    OC/LBC drive shaft work

    I had always used Ray at OC driveline in Placentia, and have used powertrain industries in GG as well. Both real good work..
  11. C

    Looking for a pair of built axles

    Whats your budget? I have a HP44 built to Wagoneer width 61" wsm, and LP9" built to cherokee width 60.5" wsm. No cheap parts used. Both currently under my daily driver until I finish the new ones.
  12. C

    1st time visiting salvage yard ( what to bring )

    bring a translator unless you are fluent in spanish, not being racist just plain fact. Good luck on the haggle part. Oh bring XJohnnyC he is a pro..
  13. C

    xj replacement

    I would rather have a Grand Wagoneer or FS Cherokee, than a 80 or 100 series land cruiser. Just the cost of the rigs, let alone the cost difference in parts between a toyota, and jeep are vastly different. I enjoy my XJ, but I love my J20 truck. If you absolutely have to have a FJ then a FJ60...
  14. C

    who is in bellingham?

    I am up here in b-ham.. dont get to drive my jeep much.. Ive been working at the yota dealer..
  15. C

    Ford 9" Detroit Locker

    Yours?
See more
Back
Top