NAXJA Forums -::- North American XJ Association  

Go Back   NAXJA Forums -::- North American XJ Association > NAXJA Unibody Jeep Technical Forums > Jeep Commander XK (2006 - 2010)
HOME Member FAQ Sponsor Info Rules Bylaws E-Mail

Jeep Commander XK (2006 - 2010) Technical forum for the full-size Jeep Commander.

Thread Tools Display Modes
Prev Previous Post   Next Post Next
Old June 23rd, 2018, 04:46
WB9YZU WB9YZU is offline
NAXJA Forum User
Join Date: Feb 2004
Location: Madison, WI
Posts: 6,941
Front Brake info

I had the pleasure of working on my front brakes yesterday. We had taken the boat out and noticed that under heavy braking the front left made a horrible grinding sound. I parked it a couple of days on the grass on the side of the house. When I went o move it, it made this shuffling sound, and it again sounded front left.

Brake service time!

I started with trying to figure out what the shuffling sound was. It sounded familiar from my XJ days. It was a rusty dust shield that had flaked off some rust due to the heavy amount of moisture we've gotten lately. Easy fix: Wire brush, rust converter, paint - done.
To get to the shield, I removed:
The Caliper (14mm)
The Caliper Bracket (21mm)
The Disc (it's probably fallen off by now)

I looked at the pads, they were not wore out, but the inner was much thinner than the outer, so I checked the caliper guide pins on the caliper bracket. Sure enough, the lower one would not move and was completely rusted in.

I think a word on Commander brake architecture would help here:
When the caliper receives fluid pressure it pushes the bores out to push the pads onto the disc. Most OEM brake systems have pistons on only one side. To make sure it applies force equally, the caliper "floats" over the pads and puts the same amount of force on the inner and outer pad.

If the pads wear unevenly, chances are the guide pins are not free to slide in and out.

*** Maintenance Note ***
When performing front brake service, at the very least, verify that the caliper guides move in their bores.
If you want to be preventive, pull the guides from their bores (yup, just pull them out!). Re-grease them with silicone grease, and push them back in. If you damage a boot - well they are cheap and easy to replace.

On XJs the caliper bracket is part of the knuckle assembly (Except the AMC models, which had a replaceable bracket).
On a XK the bracket is removable and available as a part, as are the guide pins and boots for the pins. These are apparently high in demand as the O'Reily stores in my area had the parts in stock.

To replace a rusted in guide, you will need:
A Caliper Bracket.
A Boot/bushing Kit.
A Guide Pin Kit.

Assembly of the caliper bracket:
Get some silicone grease if your bracket did not come with one.
Over each bore hole, install a boot.
Push a bushing over each guide pin (pointy end).
Apply grease to the bushing and guide pin and push it through the end of the boot into the bore.

On mine, I did the drivers side first as it was the big issue. When I slid over the the pass side and found I had the same issue. The OEM pins fit the reman bracket, so with 2 good OEM pins, I had enough to populate a new bracket. My job took 2 Brackets, a Boot Kit, and a Guide Pin kit.

Good Luck!!

Last edited by WB9YZU; June 23rd, 2018 at 04:53. Reason: Spelling
Reply With Quote

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
need help. info on brake hoses. jumpnjeep SoCal Chapter 3 May 30th, 2015 12:23
14 bolt disc brake conversion brake lines (or anyone using k20 front calipers) blondejoncherokee Sierra Chapter For Sale 0 August 19th, 2014 10:56
Cherokee Brake Line Info Locked98GC OEM Tech Discussion 0 November 10th, 2011 11:50
Ford 8.8 95 Explorer Brake info JoeyClements Modified Tech Discussion 5 September 2nd, 2009 22:05
Brake Line Info winterparker2b Modified Tech Discussion 11 November 11th, 2004 20:58

All times are GMT -7. The time now is 04:04.

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2022, vBulletin Solutions, Inc.
NAXJA and NAXJA logo's Copyright NAXJA. All content/images Copyright NAXJA 1999-2014