98xjjeeper
NAXJA Forum User
- Location
- nc
everywhere i check they either have .75 or 1.5 or 1.75. i an wanting a 1'' spacer but cant find one. can someone point me in the right direction.
-
Welcome to the new NAXJA Forum! If your password does not work, please use "Forgot your password?" link on the log-in page. Please feel free to reach out to [email protected] if we can provide any assistance.
cant find a 1'' coil spacer
- Thread starter 98xjjeeper
- Start date
Radon
NAXJA Forum User
- Location
- Saint Cloud, FL
hm.... I never have seen one either not too sure if they even make them, but they do have that adjustable spacer you can use.
NighthawkXJ
NAXJA Forum User
- Location
- Salina, KS
try looking for one for a zj, i know they make 3/4 inch spacers for them.
Last edited:
NCCherokee
NAXJA Forum User
- Location
- Anderson, SC
just get a 1.5" and cut it down.
obxtuf
NAXJA Forum User
- Location
- colonial heights, va
i bought mine from 4 wheel parts they are aluminum 1 inch spacers i believe they are pro comp brand
obxtuf
NAXJA Forum User
- Location
- colonial heights, va
yeah hey are a 1 inch spacers made by pro comp pn# 55496 they sell for around 35-40 bucks personally i like them never have to worry about them compressing because they are aluminum. hope this helps
CanMan
NAXJA Forum User
- Location
- Lake Tapps, WA
Try an RE one. My 1.5" spacer measures out to 1.625"+. You could always just do it even cheaper, add 2 more stock coil isolators. They are about 5/8" thick.
http://www.rubiconexpress.com/Products.aspx?Cn=345&Pn=1703&XnPath=320,322,345&Vid=0773C0605423
http://www.rubiconexpress.com/Products.aspx?Cn=345&Pn=1703&XnPath=320,322,345&Vid=0773C0605423
trippled
NAXJA Forum User
- Location
- colorado springs, co
i built some out of a cutting board. it was .5 in thick, so i just cut out two of em. its a special nylon type plastic that is resistant to cracking a temp changes. ive had mine out for about 2 yrs now with heavy wheeling a daily driving with no problems.
XJoshua
NAXJA Forum User
- Location
- Pueblo, CO; USA
Might just get a 3/4" spacer, then put a OE Coil spacer on it aswell.
obxtuf
NAXJA Forum User
- Location
- colonial heights, va
if you pay attention the 3/4 is for replacement for the stock isolater
Radon
NAXJA Forum User
- Location
- Saint Cloud, FL
CanMan
NAXJA Forum User
- Location
- Lake Tapps, WA
obxtuf said:
Which brand is that?
barillms
NAXJA Forum User
- Location
- Eastern Ohio baby!
Cut a 1.75" rubber spacer down to 1". Easy as pie.
green50gt
NAXJA Forum User
- Location
- Goshen, IN
This is silly. Rubicon Express. They say it is 3/4, but it's actually 1" right on the nose...not total length, total length is 1 1/4...the only part that counts is exactly 1". I physically owned a set myself.
http://www.rubiconexpress.com/Products.aspx?Cn=345&Pn=1703&XnPath=320,322,345&Vid=ED934A610274
Check it, go down to the bottom and it says 1"
http://www.rubiconexpress.com/Products.aspx?Cn=345&Pn=1703&XnPath=320,322,345&Vid=ED934A610274
Check it, go down to the bottom and it says 1"
CanMan
NAXJA Forum User
- Location
- Lake Tapps, WA
green50gt said:
Exactly. I posted the link before, some must of missed it.
fairhopexj
NAXJA Forum User
- Location
- Alabama
Rocky Road has them. They measured a little over 1".