Lincon Locker.....DONE RIGHT....

tealcherokee · Mar 3, 2006

for those who ask, or wonder, or think welded rears wont hold up.....this is how you do it

The back

http://ryan.tehbaron.com/images/spool-4.jpg

note, the corners are welded to each other, and the gear is welded to the carrier, the top bad bottom gears are also welded to the carrier on the top (center pins to the carrier)

and the front

http://ryan.tehbaron.com/images/spool-2.jpg

thats a piece of 1/4" plate, bent to fit, and welded in (completely welded all the way around) and RGD welded in, for Rigged, ofcourse

tealcherokee · Mar 3, 2006

83 views and no one has anything to say?

Jes · Mar 3, 2006

tealcherokee said:
83 views and no one has anything to say?

Too cheap to buy a spool, huh?

tealcherokee · Mar 3, 2006

na, just waitin till i got the coin to go 35 spline, then ill grab the spool

CRASH · Mar 3, 2006

Not enough wire used.

The definition of spool comes from the fact that you must use a full 11 pound spool of welding wire to burn it in.

Better luck next time.

Jeffro600 · Mar 3, 2006

Nevermind......

dmillion · Mar 3, 2006

Maybe done right, but I can't tell much from those pictures.

xtrememtbiker85 · Mar 3, 2006

I want a spool for my 8.25 but i cannot find any one who makes one. and every one else says the 8.25 is too weak to weld.

JohnX · Mar 3, 2006

xtrememtbiker85 said:
I want a spool for my 8.25 but i cannot find any one who makes one. and every one else says the 8.25 is too weak to weld.

If it is too weak to weld, then it is too weak for a spool. Essentially it is the same thing.

Also, 8.25, being a c-clip rear, you cannot enclose the center like shown about...you have to be able to install your axles right?

BrettM · Mar 3, 2006

you could enclose once side of the center... right?

(I've actually never worked on a c-clip axle, thank God)

Skullver · Mar 3, 2006

You need some better pics, those gave me a headache, maybe it was the 12er I drank last night.

littlebluexj · Mar 3, 2006

You can weld the rear of the 8.25 if you want mine is and you can weld it completly up like above by making or buying a c-clip eliminator.

nothing is imposible in a jeep!

RCP Phx · Mar 3, 2006

You dont need C-clip eliminators,if welded correctly you can still remove the shafts.

xtrememtbiker85 · Mar 3, 2006

so whats the best locker for an 8.25?

PAPXJ · Mar 4, 2006

D30...and I can still get the c-clip in and out.

Jes · Mar 4, 2006

PAPXJ said:
D30...and I can still get the c-clip in and out.

:confused1

tealcherokee · Mar 4, 2006

well....its 11 lbs of 6013

yeah, my phone sucks for pics, ill get some better ones

JohnX · Mar 4, 2006

xtrememtbiker85 said:
so whats the best locker for an 8.25?

Same as it is for every other axle. DETROIT

This is MY opinion...not trying to start an arguement.

cracker · Mar 4, 2006

PAPXJ said:
D30...and I can still get the c-clip in and out.

Dana 30 doesn't have a c-clip

BTW That looks like sh!t

ChuckD · Mar 4, 2006

cracker said:
Dana 30 doesn't have a c-clip

BTW That looks like sh!t

SPOBI!

The Disco's do have a clip.

Lincon Locker.....DONE RIGHT....

NAXJA Forum User

NAXJA Forum User

NAXJA Memeber #293 URF Racing

NAXJA Forum User

NAXJA Forum User

NAXJA Forum User

NAXJA Forum User

NAXJA Forum User

Sarge

NAXJA Forum User

Still Flailing

NAXJA Forum User

NAXJA Forum User

NAXJA Forum User

NAXJA Forum User

NAXJA Memeber #293 URF Racing

NAXJA Forum User

Sarge

NAXJA Forum User

NAXJA Forum User

Similar threads