Search results

On a 4.5" lifted XJ, what pinion angle and driveshaft slope is acceptable? My XJ have a pinion angle of 0*, drive shaft slope of 7.5* and caster of 6*. This is on a JK D44 front differential. They have a built-in caster to pinion angle of 6*.

Some time ago there was a thread about a company that repair our XJ PCM. I have one here that no longer turn on the AC compressor. Anyone knows of a place that does repairs? Thanks for your help.

What's the pros and cons to raising the frame side trac bar 1 inch? I am, doing a mockup of the JK D44 (no springs) and running it through it's cycle. When fully compressed with 3 inches of bump stop, the trac bar touches the diff cover. Both brackets and the trac bar are from StinkyFab for use...

Have any of you used a timing light on their XJ? What should it be with engine hot in park at idle? I need to do that at some point. Maybe try one of these discount parts stores for a loaner timing light. Why is a timing light no longer included in a technician's tool case? MY XJ have...

https://jacksonville.craigslist.org/pts/d/jacksonville-jeep-cherokee-xj-transfer/7584104963.html They are at 32244.

I just put up some items on Craigslist that are taking up valuable space. I need them gone. https://jacksonville.craigslist.org/pts/d/jacksonville-jeep-cherokee-xj-transfer/7584104963.html

Getting the JK D44 ready. I have some pieces from Artec for a JK to XJ conversion. Among them are a set of trusses for the inner C. Do the inner C need to be preheated before welding using flux core wire? There are plenty of conflicting statements on the web regarding the C's. All the other...

I need some for my 1996 XJ. I looked online at the usual websites but all I came across for that year had had that plastic ball joint head. Where could I get some with metal instead of plastic? On another project, I bought some metal ends and replaced the plastic.

Anyone here in Memphis TN or surrounding area? I have a JK D44 in Olive branch that need to be regeared. Any help is appreciated.

:eyes: Back in the days...several years ago, Angel Eyes headlamp were all the rage (early 2000's) to replace the OEM sealed beam. I was a follower of the crowd and got myself some. Not the fancy ones just the plain ones. They worked great for many years illuminating the road in front of my...

Does anyone know where I can get full cover for my XJ? It will be stored outdoors for a while under some trees. Trying to reduce the sap, leaves and bird dropping on the paint.

What are the signs of a bad pump? My XJ have some noise at the back of the engine that could be heard from the driver's seat as well as under the XJ. It is a ticking similar to a cylinder valve tick. It increases with engine RPM and mostly in the lower ears. Funny, I do not hear it at cold...

I am the process of replacing the timing set on my XJ. I bought a set from Rock Auto. The crankshaft gear is tighter tan the one I removed. It may fit if I tap it on. For the camshaft, it is different. At a glance, it seem to be good. however, the face of the gear/sprocket is different. The...

When a coil go bad, does the engine shut down without a warning? My XJ stopped yesterday as sudden as if the ignition is turned off. I was at about 45 MPH. I cannot get it to restart. I threw parts at it, parts I had on the self, Crankshaft, and Camshaft sensors, but I do not have a coil. I...

Years ago, there was a thread detailing re-welding the hinge to the A pillar. An after market bracket was used. I spent a lot time lookin for that bracket to no avail. I need to fix the upper hinge before it completely separates. What company sells those brackets? All help are welcome.

I think mine is bad. It no loner go into lockup. A few times this week it seem to stay locked until the XJ came almost to a complete stop. Today, it do not lock at all instead remaining 300 to 400 RPM above what is/was normal for a given MP on the highway. All fuses seem to be good. I does shift...

Were do you guys buy your gears? A few months ago I ordered a few pieces from Just Differential for a JK rear and received promptly. Great service. The diff is under the XJ for about 10,000 miles. A month ago, I ordered $700+ dollars of gears, complete overhaul kit and other pieces from...

I am putting together all the pieces to put the Rubicon D44 under the XJ. I think I have identified a source for all the pieces I will need except the drag link. My XJ is my DD so I do not plan to get outrageous with the build. I do need reliable parts though. Those who have done this before...

What companies make 2 low kit for the NV/NP 231? Depends on were I look I see Novak and/or Teleflex. Are they the same? Which would you say is the better buy?

Does anyone make long /ger steel shims for the XJ? I finally installed the Rubicon D44 in the rear of the XJ. The spring perches are longer and higher than the OEM set, 8 inches long and,... well I do not know how much higher but it need about a 3 degree shim to get the pinion angle right. I...