• Welcome to the new NAXJA Forum! If your password does not work, please use "Forgot your password?" link on the log-in page. Please feel free to reach out to [email protected] if we can provide any assistance.

Search results

  1. X

    98 First time build

    Got the separated motor compartment metal under air box tacked back to frame rail too. Sent from my iPhone using Tapatalk
  2. X

    98 First time build

    Sent from my iPhone using Tapatalk
  3. X

    98 First time build

    Think I'm going to replace hub assembly on both sides while I'm at it. Any suggestions ? Sent from my iPhone using Tapatalk
  4. X

    98 First time build

    Driver side ready for ball joint removal. Passenger side needs to be taken down to axle. Then it's time to start installing the new stuff! Sent from my iPhone using Tapatalk
  5. X

    98 First time build

    Okay. Moving forward again. Got frame rails mostly welded on. I still need to remove carpet and weld up into floor pans. One or two other spots also need attention. Sent from my iPhone using Tapatalk
  6. X

    98 First time build

    Nvm. I found it. Sent from my iPhone using Tapatalk
  7. X

    98 First time build

    Part number on this rubber fitting. ? Other side missing. Sent from my iPhone using Tapatalk
  8. X

    98 First time build

    Got it out. Had no idea took a special tool for trans cooler line. Made a tool once could I could figure out what was dealing with. It is bent in picture, was wrapped nicely around radiator line. Sent from my iPhone using Tapatalk
  9. X

    98 First time build

    Purchasing bolts, lock washers and washers. 3/8-16x1 Sent from my iPhone using Tapatalk
  10. X

    98 First time build

    Oh man. If you all roll through Pitkin look for the brown house with big metal out building down on river. Big black jeep in driveway. Silver jeep in yard. Along with other ornaments. Won't be done by this weekend however really looking forward to rollin with the crew. Sent from my...
  11. X

    98 First time build

    read up on bar pin eliminators. Cool. would be a good time to put those in.
  12. X

    98 First time build

    wow those pictures are big
  13. X

    98 First time build

    Sent from my iPhone using Tapatalk
  14. X

    98 First time build

    Thanks for the replies Smokeyyank.
  15. X

    98 First time build

    ill have to google what you mean by par pin eliminators. I have BDS shocks that will match my lift height once installed. hears to hoping those bolts dont snap. Town is too far. ON a side note. Went back to help remove junk from the property the grand cherokee was removed from. came home...
  16. X

    98 First time build

    Don't need the brace plate. Might need a aftermarket steering box spacer.
  17. X

    98 First time build

    Looked at steering box brace. cant tell if my winch bumper frame stiffener combo will negate the need for that though. guess ill find out
  18. X

    98 First time build

    IRO frame stiffeners are here. New Radiator is here. ZONE 3 inch lift with full spring sets for rear, new coils for front, new shocks Winch bumper wheels and tires lower control arms from 2001 parts jeep in my yard (some after market control arms, too dirty to tell what brand. Round arms...
  19. X

    98 First time build

    The ZJ is all junked out. Smashed in rear driver quarter panel and all broken glass down driver side. Interior has Ben pulled out and piled back in. It does have tie rod I'm after. Also upper and lower control arms may swap over. Any market for used Grand Cherokee parts ? Sent from my...
  20. X

    98 First time build

    4 jeeps now. I lied about not being close to a junk yard. It's my yard. Sent from my iPhone using Tapatalk
Back
Top