Search results

Hey guys, having a funky hiccup at idle, it happens once followed by a low idle or raised idle, depends how the Jeep is feeling that day I guess. Then the check engine light pops of for a code 22 oxygen sensor. The o2 sensor is brand new. So I ohmed out the harness to the o2 sensor all the way...

Hey guys, over the fall, my right motor mount bracket busted off the block. I removed the broken bolts in the block and went with a brown dog super bracket, and a stock style rubber mount. Over the next few weeks the Jeep developed this clunk over the next few weeks, and I was pulling my hair...

Hey guys. I’m getting an intermittent 21 code, Oxygen sensor. It’s been throwing this code ever since I’ve bought the Jeep 3 years ago. I replaced it with an NTK. Still throwing the code. Any body have any information on this issue, or a wiring diagram, possible fuses? There’s also a 12 code...

Hey guys, I picked up a 2.5” cat back exhaust system off of jegs the other day, and I’m trying to find a catalyst that will mount to the front pipe (slip fit) and connect to the muffler without any extra pipe expanding tools. I believe a 2.5” pipe will fit into the muffler inlet, I just need a...

Hey guys, my muffler rotted out on my 95 the other day, and the tailpipe is on it’s way out too. It has 2.5” exhaust with the cat removed and booger welded straight pipe to the front pipe, courtesy of the previous owner. I want to build it back to stock with a catalytic converter. I replaced the...

Ok guys, found a crack in my exhaust manifold, probably from when my passenger side motor mount bracket went. Looking for a good replacement that will hold up and not crack again. Not trying to break the bank either. Is Dorman, Omix-Ada, or crown a good replacement option? I hear the high priced...

Hey guys, I just got finished installing a new heater core and evaporator on my 95 xj. I’m taking it up the road after finishing the job feeling happy as hell that this project is behind me. I ride over a manhole cover, and hear a loud snap, followed by nasty vibrations when accelerating. I take...

Hey guys. I got an eBay snorkel kit today, and am going to install over he weekend. Anyone know what size hole saw to use to fit the flex hose through the engine bay from air box? Side note- I’m going to use edge trim-lok around the hole to avoid sharp edges, so the hole will be slightly bigger...

Hey guys, I’m planning on replacing the heater core and ac evaporator on my 95 Cherokee. Has anyone had to replace the foam used in the heater box shell, and firewall? If so, what was used. Thanks Sent from my iPhone using Tapatalk

Hey guys, I've been fixing oil leaks on my 95 xj. The back of the pan, trans plate area is soaked. I replaced the oil pan gasket and rear main seal. I cleaned the hell out of everything for a clean install. I took it out on the road, and when I got back, I'm noticing oil leaking from behind the...

Hey guys, the previous owner removed the factory door mouldings on my 95. It has that nasty 2 tone look to it. I've seen some of you guys remove the moldings and have it nice and clean under that body line. What are you doing and using to get that clean look? Spray bombing black, or vinyl...

Ok guys, I'm getting pissed at this point, I should have done this from the start, but, I needed new calipers, (old ones locking up) and u joints. I replaced the calipers, hubs and ujoints. I carefully slid my axles in upon install and put it all back together. I took her for a road test and now...

Hey guys. I'm thinking of trimming the fender from the wheel well to the bumper. Sawzall or dremel? I want clean lines, and to keep the fender flares. Should I follow the front grill line to the wheel well? Also, what does everybody treat the exposed metal with to inhibit rust? Sent from my...

Ok, so I just finished installing new hubs on my xj and I want to cover the spindle nut and cotter pin with a center cap on my wheels. When I bought the jeep, the previous owner didn't install caps with the wheels. They look like soft 8s. I don't want to spend $30 on quadratech for a set of 4...

Hey guys, I'm changing my front axle u joints, and I'm wondering if I should replace the front hubs at the same time. If so what is a good brand to buy? Napa by me wants $100 each side. Seems steep Sent from my iPhone using Tapatalk

Hey guys, I need to replace the fan clutch. It just free balls when engine gets to temp. Anybody have a brand they like? Seen a few good ones on rock auto. Sent from my iPhone using Tapatalk

Hey guys, the other day I was heading out to go fishing, and about 45 min into my trip my left front brake locked up and started smoking. I let it cool for about 10 min. I crawled under and used my fishing pliers and grabbed the inside pad and saw very slight wiggle. I then grabbed the wheel and...

Can anyone recommend quality sway bar disconnects? I hear rough country's are garbage. Sent from my iPhone using Tapatalk

Does anyone have or know where I can get all the pieces of the door mouldings and small pieces for a 95/96 sport?. They're the black ones with the red stripe. Previous owner ripped them off and looks like garbage. Thx

I recently had a check engine light come on, and the idle would drop like it was going to stall, then bounce right back to normal. It does this time to time with no light, but now it threw a light. I checked the blink codes with the 2x key switch cycle procedure, and got a 12, a 21, and a 55...