Search results

For sale: '93 XJ (Country model) 193k, 4.0, AW4, 8.25,good glass, doors, hood, hatchback, mag wheels. Seats and carpet in good condition. note: this car has been striped down for a restoration project due to floor panel rust. It is not drivable due to the gas tank, seats etc... removed. All...

Off hand, anybody know what type sensor it is, titania or zirconia?

I'm installing a new ring and pinion in a Dana 44 in an 87 XJ. My tech info is from a 1990 Chrysler/Jeep shop manual, which has a section on Comanche Dana 44's used with the metric ton package(the axles are the same except for location of spring and shock perches). It calls for setting pinion...

Off hand, anybody know the RPM at which the renix 4.0 engine achieves max torque?

I have a 01 xj, and per the build sheet, it has a 181FBI(low pinion Dana 30 front axle). My factory service manual has a dissertation on this axle, but also has a section on a 186FBI. Any body know what a 186FBI is?

Any body know what size diode to use on the 2nd gear lock wiring. The right up references one but does not give a spec.

I picked up a transmission beam(mine badly bent up)in junk yard and to my surprise the AW4 support structure mount hole are offset from my Renix. Any body know what year that changed(I found the beam laying around a junk yard all ready removed from the car). I suspect I can buy a newer support...

Off hand, any body know the axle ratio used on an 86 XJ with v6 and automatic transmission?

Anybody know the link for the write up to keep the AW-4 in 2nd gear?

FWD 01xj with up county option, 129,000 miles. At about 30mph steering wheel develops a a high frequency/rapid shimy/shake. Is noticable at higher speeds, but not as pronounced. I swapped the spare tire onto both left and right front positions, same symptom persists. Could not find and any...

Finally got the spring perches and shock mounts welded to my metric ton MJ Dana 44 limited slip axle, and installed in my 87XJ. I lowered the TC 5/8 inch and rotated the spring perches two degrees down to raise the pinion angle two degrees up before welding. It turned out good, TC yoke angle is...

Picked up a junk yard Dana 44 with a limited slip out of a 89 MJ with metric ton package for my 87 XJ. Need to figure out where to mount the spring perches and shock mounts that I will be tranfering from a bent Dana 35. Lateral position is staight forward enough, but does anybody know how to...

Anybody know what thread is used on the ends of the egr pipe? My plan is to abandon the egr system and plug the holes in the manifolds, but have been unable to find out what the thread is.

Any body know any thing about CVU fuel injectors, can get a set of six for my 87xj for $242.

87xj with OME suspension kit and xj d44 in rear, during braking the rear axle hops between 40 and 30 mph. It did not do this with the original d35. All rear brake parts are new. Any ideas?

My daughter's 01xj Sport, 73000 mi, occationally starts out in second gear and then shifts real hard into first gear right after the car starts to move, and then works normally. We put a new throttle position sensor on, but it did not solve the problem. Any idea's.

I would like to add a factory cruise control kit form Jeeps R Us to my daughters 01 xj. It seems straight forward enought, only question is, will there be wiring and connectors behind the plugs in the steering column where the control switchs go? Thanks for any insight.

My daughter is having some problems with her 87xj in Indianapolis, IN. Can anybody reccomend a mechanic in the area proficient in RENIX. She lives right inthe center of downtown.

A/C cools very well, but under certain conditions when it is very hot under the hood, the A/C clutch will not engage. I have 14volts on the battery side of the relay and 12volt on the feed to the A/C clutch side of the relay and close to zero resistance in the wire to the clutch. I put in a...

My o1xj shop manual shows a "trailer tow group electronic brake provision" in the wiring diagrams for the trailer tow group. The wiring diagram shows a wire coming off the headlight switch, then to the junction block and then some where to provide fused power to the electric brake controler...