Search results

A lot of threads with photos have a message where the photo should be that says please update your account to enable 3rd party hosting. How do I do that? I haven't been able to find anything under user co unless I am missing something.

Ok. I am getting ready to start buying stuff to do the swap over the winter. For those of you that have done it what are some problems you ran into or things you would do different. I'm looking at a 6.0 swap. I have access to i think it's a 04 2500 4x4 with a 6.0. I just don't want to buy...

I'm running 2014 Rubicon wheels with 1.5 in adapters right now. I just bought a set of 315 70 17 bf all terrains. Now I forgot all about the back spacing on the factory Rubicon wheels . Do I need to buy new wheels to have these tires installed on to keep from rubbing on control arms? 6in la...

Ok I searched and maybe using the wrong search words. I have a rcouple rear cvs drive shaft in my cherokee. One of the u joints is bad. I know it's a 1310 series. Napa, autozone, and advanced can not cross reference to get a part number. Does anyone have a part number for one of those places...

Ok guys and gals I have a model 32 tubing bender went through a nasty divorce and my x took my tubing bender and stashed it at her boyfriends house. I went and took it back after I found where it was. Anyhow the dies have rust on them now. What's the best way to clean them. I'm not sure what...

Ok I did my xj in Monstaliner and am thinking about spraying some military stencils on. How would I go about making it look old? All ideas welcome.

Well I have been looking for agate manual window door panels for months now and have had no luck. I'm about to the point of just changing over to power locks and windows. Anyone known if the wiring is already there on a 1998 cherokee. Hoping all I need is to just get all the internals and...

Have 2014 Rubicon wheels but found a set of Nitto Terra Grappler G2 315 70 17r. Just trying to see if anyone has ran this size on factory Rubicon wheels.

Wanting the black or agate interior. I need everything. Anyone close to North alabama have the stuff. If you have a parts jeep I can pull everything. I need manual windows door panels. 256-497-2561

I just got finished swapping over to rear disk. I got the disk set up off a 96 grand with dana 35. So after bleeding 4qts of fluid through the brakes the rear brakes will not stop the wheels turning while idling on jack stands. No I have not swapped the prop valve. Could that be my problem? I...

I know this has been beat to death. I did a search an read all the threads. I still have a couple of questions. I got rotors, calipers, backing plates, well the whole rear en out of a 96 grand cherokee with disk brakes. i didn't get the prop valve or master cylinder. from what I read the xj...

I got a free one but it is shot. I live in Athens Al. If you have a complete xj with good grey interior with a good external slave ax15 I may be interested in the whole vehicle as long as it not 97 newer. Or if it is a 97 or newer with tan interior I would be interested

Well I will be picking up a 89 mj pioneer 5 speed, 4x4, short bed. That I traded work for. I found a complete 99 xj with 5 speed in junk yard. I am pretty much swapping the owner a 98 xj for the 99 . Basically I was just going to do the ax 15 swap but now thinking about swapping engine tranny...

http://www.autotraderclassics.com/classic-car/1988-Jeep-Comanche-1394094.xhtml?conversationId=1320453 Tommy archers race truck.

Ok my out put shaft bearing on my sye is bad. I can move the yoke up and down. So I have a extra sye and am planning on replacing the housing that has a new bearing in it. I have been trying for a couple of hours to get the old housing off the out put shaft. Does anyone have any pointers or...

Ok regular driving any speed no grinding or vibration. If I barely press the gas pedal say 1/4 in then I get a constant vibration until l let off gas or press it further. Coming to a hard stop a bad grinding vibration from the front end that will go away if I let off the brakes and then easily...

It's happened about 4 times in the past 2 years. Starts runs fine no codes or check engine light. Symptoms are back out of drive or start from a stop light when you first press the gas it just falls on its face doesn't stall or die just no more power than a little above idle. Let off the...

Ok so I have a 4.5 la lift,sye,4.56 gears, Aussie lockers f/r, frame stiffeners, 31x10.5, installed now. I have a 12,000 lb winch and steel to build my bumpers. Still need steel for rock sliders, swing out tire carrier, and roof rack. Have 2 hid driving lights to mount on bumper and 4 hella...

Anyone know of a higher amp alternator that will work on a 98 xj ? Been googling and searching on here but not much luck.