Search results

looking for a d30 with 4.10 gears. looking for a high pinion. may consider a Low pinion. let me know u what u have through pm

I got these Datsun 280z hood vents and I had never installed them so go figured it was time. First I made a cardboard template The I started cutting and the next thing I knew I had 2 big holes in the hood!!! I also positioned them so that the left vent opening was not directly over the...

I just did a SYE on my np231j so I have the main shaft and the rear retainer for sell. they are in very good condition. I will ship. Make me a offer. they are parts 27 and 35 in the break apart picture

I have a custom made drive shaft that came on my comanche when I bought it. It's was to short for my lift still, so I just did a sye and had a new Tom wood drive shaft made. So now this one is up for sale to recoup some of the cost. Specs: 41 1/2 inches from center to center. It is Aluminum...

I am hooking up a B&M Trans temp gauge and a after market trans cooler. It says to hook up one wire to illumination/ dashboard lights but I have not Idea which wire to splice into. Also It says to run one wire to the ignition wire, once again I have no idea where this is located. Sow help...

so I was having some overheating problems and I am replacing my whole cooling system. I put on a high flow 195 degree thermostat, flowkoolor water pump and am in he middle of installing a CFS 3 row radiator and the HD fan clutch from NAPA. I just put the clutch and radiator in for a test fit...

hey guys so I started a thread on my MJ on cherokeefourm.com check it out and tell me what you think. I would start it again fro this site but It would take hours, so here is the link. http://www.cherokeeforum.com/f46/1988-you-aint-chancin-unless-your-manchin-build-143298/index4/#post1973277

alright guys so I am replacing the whole cooling system and the trans lines are leaking because the mj has been laid on its side, the upper control arm was shoved in the metal lines and it have pinched the, so now im getting all new lines. I thought I bought all i need but apparently I just...

SO I pickets up a flex a lite trans cooler and B&M trans temp gauge, so now my question is whats the best way to hook it up? Should I hook it up inline with the radiator or should I bypass the radiator completely? I am also hooking up a brand new cfs 3 row all metal radiator and a HD fan...

So I have a 1988 jeep comanche 4x4,4.0. the tie rods need replacing and I need a alignment. I want to get rid of the "Y" steering set up and I'm looking at 1 ton steering upgrades, So far I have came across Seriousoffroad.com's set up and JCR's. they both look very similar to me. Whats the...

Im buying a new radiator for my 1988 4.0 jeep comanche, It has the closed loop style cooling system that the renix engines had. Im looking for a good aftermarket radiator. I have a few questions 1. Is a 3 row better than a 1 row? 2. Whats a good brand? I also am going to run a HD fan...

Ev1 style stock 4.0 injectors for sell, I believe they are good from 87-98 years. Correct me if I'm wrong. They came out of a 88 mj, I just upgraded to 703's so I have no need for them. They are currently still in the Jeep. The jeep has 100k on it so these injectors should still be good for a...

I have a renix 1988 jeep Comanche 4.0. I have just put a pacesetter header on and installed everything back and I am leaking fuel out of the top of the fuel injectors where they go into the fuel rail. My guess is maybe the o- rings are bad? But all of them are leaking. I feel like it might...

Who makes this rim and I need specs, I want it!!!

Im putting a pacesetter header on my 1988 Comanche renix 4.0, I want to put new bolts/studs on when I replace the header and pull the intake off. Where can I get them. I already called the dealership and it would take them a week to get in and cost around 80 bucks! Is there other options what...

Hey ya go. winching out that cJ5 on swampers!!!!! Im not going to lie though, Its a Bad B**** when Is not stuck in the never ending bottom of Madagorda,Texas Bay. This is it...

Here they are But first I had to do some cutting.... Then the Gf Made some Dinner for our hard work! Still got some work to do. I need to hook up all the lights and mess with the back bumper. Its not letting the tail gate open properly. HOPE YALL LIKE!

Steering knuckle backed out. Went to fix it and now the ignition is stuck on I have a 1988 Jeep comanche and I went to tighten up the four screws around the steering knuckle because the have backed there self's out and followed this video. I...

Hey guys does anybody want to get this event together. General SAMs is a mild park and great for beginners or people that want to take there daily drivers out. There is also a more advanced area with a hill/rock climb. This would be fun to meet and greet and drink some cold beverages...... And...

Which naxja chapter includes Texas? Didn't know if I was missing somthing or there just wasn't one.