Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Welcome to the new NAXJA Forum!
If your password does not work, please use "Forgot your password?" link on the log-in page.
Please feel free to reach out to [email protected] if we can provide any assistance.
99 XJ 5 speed 4.0
Okay so maybe someone on here can help me out with this. I have an np231 with an Sye kit in it. The tail shaft seal leaks. IM giving it a quart of atf fluid almost every a week. The seal is an easy fix that i am more than capable off doing. The trouble is Idk who makes this...
Well you guys are never going to believe this. A few months back my fully lubricated transfer case locked up on me on the highway. Snapped the driveshaft like a twig and and the dticeshaft hit my bell housing cracking the bell housing and one of the ears of the motor. Which was causing the...
Hi guys. Just tested the connectors at the ambient air temp connector getting 4.95 volts at the batt temp connector I'm getting 2.85 volts. I also noticed my over head console the DTE reading reads OC what is that over charge open circuit??
99 XJ 4.0 AX15
Gas Gauge does not work and check engine light is on.
The code is p1492 ambient/ battery temp sensor voltage to high. The Alternator is not charging the batter. I replaced the battery temp sensor r the battery and the alternator. And i still have the same problem. I am at a loss...
99 XJ 5 speed Dana 35 4.5~5 inch lift
my original transfercase locked up and died. i was able to but one from friends that has an sye in it he does not remember what brand the slip yoke eliminator is. I measured from transfer case yoke to rear axle pinion yoke and it looks to be about 34...
I bought a bell housing found some bolts have three for the time being seems to be fine I think my mistake when I did the throwout bearing was not putting those top bolts in
I will look for an threaded hole when I get home. As for how the drive shaft managed to do this idk. I go to porter and Chester institute for automotive it is a technical school it was shop day and I was under my jeep putting a new upstream 02 sensor in and my bell housing and trans bolt ear...
Im going tonsee if I can find someone willing to try that. as for running with the broken ear I tried that just in my driveway. got an awful scrapping noise when pressing in the clutch cause the trans is shifted to one side I noticed last time I took this trans out which was to do a throwout...
99 XJ 4.0 Ax15
Was driving home from school yesterday on the highway when the 2 month old u joint bindrd up on me and caused the rear drive shaft to propel underneath my jeep. Buddy came to the rescue with a tilt trailer and a pickup cause I had my front one out while I was rebuilding upon...
ik the throwout bearing pilot and pressure plate and clutch disc were replaced. nto sure about the flywheel the transmission shifts smoothly through all the gears except 3rd which is a worn syncro
99 XJ 4.0, AX15, NP-231 okay so i got a grinding/scraping noise when my foot is on the clutch pedal it ocasionally will go away when it is fully depressed and come back at about 1/2 way and sometimes it will do it no matter how much the pedal is depressed. im thinking its a bad throw out...
99 XJ 4.0 AX15 about 5 inches of lift
My Cherokee has about 5 inches of lift it currently has rusty's shocks and a 6 leaf pack in the rear it does great in turns and ive put car trailers with cars on the back and have gotten very little saggage but it rides like a brick would a different set of...
so what you are saying is the M.O.R.E poly mounts arent as good as the rubber mounts? Also i took a look at the brown dog website there are alot of different stuff on there and im not sure which i would need http://browndogindustries.com/cherokee-xj-1987-2000-40l.aspx i think i would need...
1999 XJ 4.0 AX15, NP231
Hey guys, My XJ is going to be need a new set of motor mounts sometime soon i was wondering who makes some good ones. I'd like to stay away from the autozone ones cause i had a friend use them and they werent all that great. (what's your experience with them?) How about...
my death wobble was caused by shot tie rod ends prior to that it was caused by the awful track bar i had in it. another thing that can cause death wobble is imbalanced tires also check your ball joints and as other said control arm bushings could be a culprit as well but 9 times outta 10 its...
A friend and i ran into an old XJ behind a an old warehouse. it's a 1984-1986 with a 2.8L v6 however it is the Cherokee Chief and it is fully loaded with power everything. it has the selec-trac transfer case. this is our first time ever seeing a selec trac transfer case like this it had the...
So we took out the transmission out of the my took it apart and found that the input shaft bearing was done and 3rd and 4th gear were destroyed. Thus all started after putting 10-30 in it my guess is the 75=90 that was in it acted like engine honey. We set out to find an ax15 we found an ax15...