Search results

How could i put one behind my AW4? difficult?

So, i finished my pack today... does pretty good, but for some reason, the front of the pack unloads and bends my main leaf... why is this??

Ok, here's the deal.. my '91 xj, aussie locked in the Dana 30 and an np242 transfer case has a problem. I put the thing in 4 wheel drive part time (High or Low) and sometimes it works, but most of the time, the front driveshaft just goes back and forth and it sounds like slipping gears... i...

My engine makes a funny knockin noise, most of the time at idle. sounds like somethin may be hittin somethin... i dont know. any ideas? It's the 4.0 HO on the '91 model Laredo

in doing this with my unibody xj, am i gonna have to support everything somehow since the hatch (main support for unibody) will no longer be there? if so, how can i do this cheaply?

will a grand cherokee starter fit my xj? and does anyone have a starter for cheap?

Hey, this is just like lettin ya'll know what i did. I ripped the carpet out by pulling out only the front and rear seats. most of it comes out pretty easily. most people like rhino liner and what not and are always looking for alternatives that are cheaper. a buddy of mine used something...

Tried to search, but we don't really get along too well. So i need to replace my headliner but cant figure out how to remove my domelights... THERE'S NO SCREWS OR ANYTHING. It baffled me. Any help would be freakin sweet!! Thanks ya'll.

at left lock or around there, there's a loud pop and i can't track it down, well... i've got it down to the steering box and shaft and whatever is there behind the dash... I heard from a friend that something comes loose on the u-joint in the steering shaft when you have 31s or above... I have...

I've got a '91 XJ with np242, about 5 inches of lift, stock control arms, rough country adjustable track bar, and unbalanced 33 inch A/Ts. When i turn left, i get death wobble... But never Right??? What's up with that??? I know i have like 3 things i need to do to fix this but im i poor high...

I need to do this to get more droop. Will it weaken anything?? Pictures would also be nice. Thanks

I've got about 4.5-5" of lift on stock lowers. I need some new ones but i'm pretty low on the funds. So if anyone wanna sell some for a good deal, please let me know. Thanks

I'm lookin for a Chrysler 8.25 or Ford 8.8 in the south Mississippi area. Low budget. Let me know if you got one.

I was messin with the bolts on my crossmember on my '91 XJ, AW4(? its automatic) and NP242 TC. Well, since I'm so beastly strong, I managed to spin the head right off of one of the bolts! How bad is this?? Should i probly fix that soon?? Thanks all.

I'm tryin to pull the passenger axle from my dana 30. After removing the caliper, rotor, and 3 13mm bolts. It should slide right out right? Well, i've been poundin at it and trying everything but it hasn't budged. Is there a cclip i have to remove. This is a '91 hp 30. Thanks.

I've discovered that my passenger front wheel bearing is shot to hell (Can't drive on it at all)!! Here's the deal: At least $130 for a new wheel bearing, $70 labor (dont have access to a ginormous press, and i dont have that much. This is my Daily Driver so I started brainstorming for what i...

Wow, i took off my front drive shaft and get no vibes whatsoever. My jeep drives like a Mercedes not at most speeds (except for the body roll and spool in the rear muahaha). So anyway, i do have a worn out u joint in that ds but does this cause vibes or could it be that its out of balance...

Well, my lockrite is for what we think to be a chrysler 8.25" axle, so tomorrow im weldin up the gears. if i dont like it, were just gonna cut it all out w/ a torch and put my friends old spider gears in. I'm also w/in a few months gonna be gettin an 8.25" for like $100 locally. Just lettin...

Will Up Country skid plates fit on my '91 Laredo and is the 1/8" steel worth it? I have AW4 tranny and NP242 TC. Thanks for the input.