Search results

I have a AW4 out of a early '90's cherokee. I got it from a friend that was parting out a cherokee about 4 years ago. I was told it was running great before it was pulled. I don't think I'll be needing it any time soon. Comes with flex plate and converter. $50. Bryan

I've decided to part out my D35 since I can't seem to get rid of it whole. Here is whats left. Right and Left axle shafts for non c-clip D35 - $20 ea. Used spicer R&P 4.10 ratio and open carrier and pinion yoke - $50 Drum brake assemblies (drums, shoes, hardware, backing plate, brake cable) -...

I found a wonderful addition to the jeep the other day. If it were anywhere but the leaf spring hanger I wouldn't worry about it. But with the twisting forces appied to the area when on the rocks, I don't think it will last very long. I have some fab tools that includes a welder (although...

Is it hollow inside, meaning, is there an inside panel and an outside panel with about an inch of space between the two, with bracing spaced throughout. Or is there only one stamped panel.

I'm need a new coolant temp. gauge for my '87 XJ. Not sure what years will interchange. Let me know.

Does anyone know what the resistance should be on the coolant temp gauge sending unit at normal engine temp? I measured it at 100 Ohms. I also took the wire off the sending unit and placed it to ground, and the gauge didn't peg out at hot. So I'm thinking the gauge is bad. Do you think my...

I'm planning on putting a 10" sub in my '01 dodge ext. cab. I've found a place that makes some custom sealed enclosures that fit under the rear seat. My question is, does it make a difference in the sound if the sub is firing down or forward? This company has a single forward firing box, and...

Well I'm not, but my parents are. Did the 97 to 02 cherokees with an auto have the aw4 four speed? Or did DC go with the three speed like the TJs.

Well, I finally have an excuse to buy a new exhaust on my '01 cummins. The tailpipe rusted off right behind the muffler. My question to you guys with experience on the subject is, what 4" turbo-back exhaust do you recommend? I'm looking for a system that is not extremely loud, and is as cheap...

how to thaw out some washer fluid lines? My dodge won't spray washer fluid on the front windshield. I checked the washer fluid, it was low but looked like it was a little slushy. I got some new fluid that has a freezing point of -20*F to dilute the cheap autozone stuff I had in there, hoping...

Cleaned out the garage today and decided I had a few things that are taking up too much space and got to go. Stub shafts, caliper brackets, spindles, knuckles, and new calipers for '79 ford bronco front d44. Front D30 w/disconnect from an 87 XJ. It has 4.10 gears and Currie HD steering...

I am looking for the ground that goes to the turnsignals, and dash gauges. I'm pretty sure I have a high resistance somewhere that is causing all my gauges to not read correctly, and my turnsignals are dim and slow? If anyone knows much about this it would be a great help.

When I did my rear 9" swap, I bought a set of leaf spring perches from MORE. The perches had 3 holes for the center pins, one in the center and the other two were an inch forward and an inch back. Is it a good idea to move the rear axle back an inch by mounting the center pin in the forward...

Anybody know what is the thread size of the two ports on an 87 XJ? Are they standard or metric, and what TPI/pitch are they? Thanks

I pulled off my steering box last night to swap it out with a durango box. I figured while I was there I might as well make new spacer plate that would also sleeve the frame rail (similar to c-rock). After I got everything off, I noticed that the frame was already sleeved from the factory. My...

I went to the local parts store today to get some pricing on a box for this swap today. I asked for a 98 durango v8 4x4, and it turns out they offer two boxes. One with snowplow package ($205 w/ext.), and one without snowplow package ($250 w/ext.). Has anyone that has done this swap ran into...

Can somebody get me a lenght (or height, depending on how you see it) measurement of an RE 5.5" coil with vehicle sitting at ride height? Its been so long since I took it apart that I can't remember the measurement I took. 4.0L up front without winch or heavy bumper. Thanks

Need some quick info on what bolt size is used to clamp the ford radius arms to the axle. Thanks

Are they a good idea or not? Specifically, I'm looking into getting a 1.25" -12 TPI UNF threaded bung for my custom radius arms I'm making. I'm going to weld a threaded stud to the RE flex joint at crossmember, and thread it into the arm so I have some adjustability. Just wondering what...

I was on RE's website and noticed that they are offering two new HD super-flex joints, one using 5/8" bolt and one use 3/4" bolt. Does anyone know if the HD joints offer the same degree of missalignment as the two non-HD super-flex joints? Bryan