Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Welcome to the new NAXJA Forum!
If your password does not work, please use "Forgot your password?" link on the log-in page.
Please feel free to reach out to [email protected] if we can provide any assistance.
So I rebuilt my NP231 when I installed my SYE kit, my speedometer worked before I pulled the transfer case out but now it does not. I made sure that the cable is plugged in on the transfer case but no dice. Any advice?
Hi guys, so I upgraded all of my factory wiring so,that I could do the alternator upgrade. I got my new alternator in earlier today and after some headache, I got the new one to fit back in the place where the old one was removed. My issue is the new case is larger and the alternator hits the...
So I’m rebuilding my transfer case and I’ve replace all the bearings except for the incredible pain in the ass needle bearing that is in the smaller case half, I cannot get a puller to fit. The guy at the auto part store said something about moist bread, but that sounds about as reasonable as...
Hi guys so I’ve been tackling my ball joints today, and they were a pain in the ass to remove and so far have been a nightmare to reinstall. I was able to put the bottom in with no issues, I cannot figure out a way to get the angle correct to reinstall the top one. My problem is arising at the...
Hey guys, so I have decided to go ahead and pull the trigger on replacing the garbage rear drums on my XJ, I have heard that the KJ swap is a direct bolt on swap, so I figured this would be the way to go. What I am wondering is what all I need to complete this swap. I’ll list what I think I’ll...
Okay guys, so I rebuilt my TC over the weekend and installed an SYE kit and then my brother in law hit the gas and not the brake pulling in my garage and knocked the case off my work bench and the case is now destroyed. I have a budget of 1500, for a new case and am thinking about either an...
Hey guys, I have removed my transfer case and I am rebuilding it and installing my SYE, and I have the whole case torn down and I have the large retaining ring out but the gear set still won’t budge. Anyone know how to remove it? Thanks
Hi guys, I am attempting to remove my TC today to install my SYE and its giving me fits, does anyone have any tips or tricks? Also what is the best tool for removing the bolts?
I have for sale two sets of spidertrax adapters to mount Jeep Wrangler wheels onto an XJ. Paid 200 for them, asking 125.00 shipped to you.
Sent from my iPhone using Tapatalk
Hi all so I picked up a 1995 XJ a few years ago with big plans on building it up. After some personal set backs and even more business failures, I am finally in the place to build my jeep the way I want. I am starting with a 1995 4 door and plan the following for my build.
6.5" IRO Long Arm...
Hi guys, I am starting a build on my XJ this weekend finally and I have a few questions about Monstalining it. I have heard good and bad opinions about spraying it vs rolling it. If I did decide to spray it, What is the minimum air compressor I could get away with? Ive heard that with a...
Hi guys, so I ordered my IRO LA lift for my XJ on Friday and since I will be running 33x12.50/15 tires, I figured I would go ahead and freshen up the steering components some and replace my old ball joints. I am looking on rock auto and they have offset ball joints that say for lifted vehicles...
Hey guys, I’m getting ready to put a long arm system on my 95 XJ, I want to run 33x12.50’s on 15 inch steel wheels. What size rim would you recommend? Do I need spacers? Thanks.
Hi all I am getting ready to pull the motor on my XJ in a month or so and begin my rebuild. I plan on fulling building the XJ up now that I got my dream job and money isn't really that much of a concern. What I am curious about, is can I make my 1995 4.0 use the auto belt tensioner on the...
Can I mount a 12.50 wide tire on my Moab rims and put them on my XJ? I have them on there now but they aren't that wide. I'm wanting to up my lift and put 33x12.50 km2's.
Sent from my iPhone using Tapatalk
Hi guys, so I am having an issue with sudden overheating. My jeep overheated pretty bad last summer, so about two months ago I replaced the fan clutch, AC electrical fan and the belt and did a full coolant flush and the jeep has been running great with cold AC and the needle never going above...
Hi all, so after owning my 1995 XJ for about 3 years, I purchased a 2017 JKU Rubicon Hard Rock over the weekend. I have a few questions about the XJ before I put her up for sale. She is mechanically solid, but last friday I took her out wheeling and when I would engage her in 4WD high, the...
Okay so I put on a RC 3.5" lift last year in order to clear my Moab's, the lift itself is decent but the coils and the shocks are garbage, any suggestions on replacement parts for a 3.5" lift for now? Thanks guys.
Sent from my iPhone using Tapatalk
Okay, so just as the title says, what do I need to do the the electrical side of the xj before I take a millermatic 215 to the underside of my 95 sport this weekend? I bought the JCR full frame stiffeners. I've put this off for a while and finally got my new welder in and figured I'd tackle...
Hey guys, I'm looking to buy a welder, preferably Mig and want some advice as what to buy. I have a dedicated 230V receptacle in my garage that isn't being used. I want to build my own bumpers out of 3/8" steel, I also will be making knives and forging Damascus steel. Thanks in advance. My...