Search results

Here is the thread i found info on. http://www.greatlakes4x4.com/showthread.php?t=248779

I did some quick research when i saw the ad for it and it sounds like the 5 pin connecter that is supposed to be compatable with most 5 pin connectors is not right for the m8000. Not sure if they all used the same pin outs over the years but you could always chop the plug and wire direct to the...

i just cut the rubber hose coming out of the compressor and shoved a barbed fitting in it then used some pipe nipples and reducers to connect it to my seperator. you want 2 good quality hose clamps or it will blow apart. no problems with this setup running long enough to air my 35's from 15 to...

i have had the kevlar sidewall mtr's for 2 years now and like them. it took a bit of weight to balance them but no death wobble. my only complaint is it takes a lot of wheel speed to clean the sticky mud out but on dirt and rocks they are way better than my km2's were.

i ran a welded 8.8 for a year before i saved up for my arb. I'll never go back to welded again. selectable lockers are so much nicer. They are there when you need them and not when you don't. I find it fun to try things with the front and rear open first then start locking up axles as i...

i am using the generic elm327 adapter from amazon http://www.amazon.com/gp/product/B004KL0I9I/ref=oh_details_o01_s00_i00. i am currently using the free version of torque on my samsung galaxy s2 (att model) works great probably going to buy the full version soon. just make sure you pick a seller...

Vehicle info. 1996, 4.0l, 5spd, 2 door, obd2 ok so i have a rough idle and it is kind of random and my mpg has gone way down. So i stating checking things to replace. all new plugs wires distributor and cap so far since they where on it when i got it years ago decided it could only help...

bought one from autozone for my 96 and had the same issue.

Ok so i did the tests sidewinder cc described. With the pcm connected i had continuity and with the pcm disconected i had no continuity. So it sounds like i need to get a new pcm... anyone go a pcm for a 96 manual transmision laying around for sale cheap? i also tested the the cts and its...

Thanks sidewinder cc for the info. I hope to be able to check things out tomorrow after work. I Did try multiple relays that are know to be good. I have been having some performance issues lately. It likes to stumble when cold and some times on the trail it will stall and not restart for 10...

no check engine light that i noticed but i will check for codes next time i get a chance. Didn't get a chance before i had to leave to find out how to check the coolant temp sensor. Figured it was a simple on or off kinda switch switch so i tried it unplugged and with a jumper wire in the plug...

already tested the relay. if the ignition is on the relay turns on. I had someone turn the ignition on and off and i could feel the relay click on and off. I put the voltmeter in the sockets that control the relay and it is getting power when the ignition is on.

I was having the same problems replaced the CPS and all was good for a while now it still does it everyonce and a while. i will have to check my fuel pump and filter.

So my aux cooling fan is running any time the ignition is on. This includes at cold start up so its not from the engine temp and my ac is removed and i made sure my heater is not in defrost. It turns on and off with the ignition. I have tried putting a jumper wire in the temp switch and...

i just found my pop noise and it was the track bar mount on the axle end the bolt was slopping around in the hole. have someone turn the steering back and forth and watch the bolt and see if it is moving side to side. if you think the bushing is shot they are cheap to replace if it uses the...

I stated welding mine with flux then was quickly inspired to go get my tank filled. Have fun finding a comfortable position to weld in if you are stitching the outside edge to the frame. I have the tnt stiffeners and it was a little tricky finding a good angle on the top side since it is so...

i just looked at the 8.8 i got for my xj and had some questions. How close is the the spring to hitting the caliper bolt? it looks really close on the one i bought that was already in a xj. So i guess the question is will you be able to remove the caliper bolt or is the spring in the way?

ok so my plan is to put a 1/4" plate running from under the bumper mount to the end of the bulkhead. then cut out the back of the box and the corresponding plate. this should leave a peice above the hole that is around an inch and lots of surface area on both sides. then weld the plate to the...

actuall y i made a new post in the right section but i don't want anymore lift so a shackle relocation kit isn't going to work. in order for a boomerang shackle to clear where i'm hitting it has to be a lift shackle and will still be limited by the back of the box. heres the new thread in the...

jeeperjohn how much did you trim out? ok i found the thread from when you did yours http://www.naxja.org/forum/showthread.php?t=993590&highlight=cutting+shackle+box so i see how you did it. how long are you shackles? how much hard wheeling have you done with it cut out.