Search results

I am looking for a new to me xj between years looking for a new xj between years 93-97 miles don't matter as long as the interior can clean up well.

I will take another look at maybe going to a 16 in rim and 305/70R16 duratrac which equals a 33/10.7. I was also looking at the general grabber at2s

what about mickey thompson atz

I was going for an AT, I have never had a problem with my firestones, but are they really the best best for the above mentioned?

A little off topic, but I am looking for the best all around all terrain tire for my 1995xj because my 33x10-50 bfg at are wearing out. I already have Firestone destination ats for my kj 265/75/r16s for when the lift gets installed. I am looking for my xj now. I want a tire that will overcome...

My XJ is overheating in traffic or at a stand still with the ac on or off. The electric fan is working. The waterpump, thermostat, collant temp sensor (on the side of the engine), radiator, radiator cap, and fan clutch are brand new and at this point I am dumbfounded on why this is happening. It...

My XJ is overheating in traffic or at a stand still with the ac on or off. The electric fan is working. The waterpump, thermostat, collant temp sensor (on the side of the engine), radiator, radiator cap, and fan clutch are brand new and at this point I am dumbfounded on why this is happening. It...

I am experiencing oil burn problems. I cant figure out if it is the rings or valve seals. The engine is not driven hard and has 200k miles on it. The only time I see where it is burning oil is once in a while during initial start up or at sudden spike of rpms. If it is the seals how hard are...

How hard is it to replace a rear main seal and I also heard that it is in my best interest to also change out the oil pump. Its lifted so I know the oil pan will come off easy. also if maintained is an aw4 a decent transmission even at 200k if well taken care of. 1995, 4.0l, aw4/np231...

is a stock np231 with an sye ok if im running 4.10 and 33x10.50 or should i go all out and do a wide chain cause My last np231 lasted 200k miles and the chain stretched out and caused failure in the 4wd area or is 200k miles about time for a new t-case

I did just that an noticed that it was number 4 cylinder

I have just noticed that I am burning oil. I cant tell if it is the valve seals or the piston rings. It doesnt burn it all the time just when i first start it and when i sit at idle for a long time. even when i first pull up and park it doesnt burn it just when i leav it idle. 1995...

are cold air intakes a good choice cause thats about the only modification i didnt do yet

im already getting 20 city and close to 22 hwy but i have heard people getting 24 with them and im trying to achieve that. its a stupid little goal i want to accomplish. its already not stock, I have 3.73 ratio, lockers in the front d30hp and destination mt 31in which is more like a 32...

what is the best way to improve gas miliage with just bolt on parts and along with helping the engine last longer as well. 95, xj sport aw4, np242, d30hp/35

What are the torque specs for 1995 Jeep Cherokee 4.0L for main rod and bearing and support brace? 1995, 4.0l, aw4, np242, d30hp/35, 190,000 miles

should i do a main and rod bearing job while i have everything apart, or should i leave well enough alone. i already am gonna do the oil pump and pick up with a milling 20% more volume than stock.

is it an easy process is what im trying to get at

How hard is it to change out a rear main seal/front in a cherokee, is there a write up, and should i change out the oil pump while im at it? 95xj sport 4.0l aw4, np242 aussie d30, 35c limited slip soon to be 8.25 superior 190,000 miles

i have the dual diaphram booster. and will it help if i do a rear disc for my 8.25 im building.